Craftsman 113.248510 owner manual GU,DEsuPPO.TIIl-r L, Upperblade tl t

Page 27

4.Loosen the setscrew which locks the blade guide support and push the support all the way back. Repeat for lower blade guide support.

UPPERBLADE tl t

GU,DEsuPPO.TII_l-r L

SETSCREW _

"<_-_-"_,J/l[I L.U ql

I '1

GUIDE

SUPPORT

5.Loosen the setscrew which locks the upper back up bearing and push the bearing all the way back. Repeat procedure for lower back up bear- ing.

_---_--_--'=_SETSCREW

_f

UPPER

BACKUP

 

BEAR

NG SETSCRE_

LOWER BACKUP

BEARING SETSCREW

WARNING: TO AVOID SERIOUS EYE INJURY OR SCRAPES IF THE BLADE SHOULD SUDDENLY

UNCOIL, WEAR SAFETY GOGGLES. CAREFULLY

UNCOIL THE BLADE HOLDING IT AT ARMS LENGTH.

6.Uncoil the blade.

7.Place the blade over the wheels with the teeth pointing downwards toward the table as shown. Make sure the blade is between the blade guides and is in the center of the rubber tires.

NOTE: If the blade wi!t not reach around both

wheels, lower the upper wheel by turning the tension knob counterclockwise.

BLADE CENTERED

ON RUBBER TIRE

27

Image 27
Contents Save This Manual For Future Reference 113.248320113.248440113.248510 Table of Contents Keep Guards in Place Know Your Power Tool Ground ALL ToolsKeep Work Area Clean USE Recommended Accessories Never Stand on ToolBefore Each USE Additional safety instructions for band sawBefore Using the SAW When Installing or Moving the SAWAccessories Before SandingWhenever SAW is Running Glossary of terms for woodworking Power Supply25 Ft 26 50 Ft 100 Ft Motor Safety ProtectionWire Sizes Sawdust from interfering with normal motor ventila- tionGeneral information Unpacking and checking contentsDescription QTY Loose PartsPan Hd. Screw 10-32 x List of Loose Parts in BAG #507968Truss Head Screw 1/4-20x12 List of Loose Parts in BAG #508014Nuts Support Bracke Leveling Foot Assembly and alignmentModel 113.24821 O Attaching LEG SETDescription Qty Truss Head Assembling Cabinet Model\ ,/o Mounting the SAW to the Cabinet From loose parts bag find the following hardWare Front Find the following parts Model 113.248210 onlyAttaching the Handwheel Mounting the MotorModels 113.248440, Tighten Flange NUT After Tensioning Beltwith Wing NUT Steps are Completed Connecting the MotorSelecting Blade Speed Recommended Speed SettingsChanging Speed Settings Model 113.248320, 113.248440Attaching Trim Caps MODELS113.248210an¢ Getting to know your band sawModel 113.248440 & 113.248510 on LY Location and function of the electronic indicator systemOpen Battery Open Battery Cover3000 Using the Electronic Indicator SystemFunction Keys Read-out Indicates correct tension forJrt,t Installing the BladeUpperblade tl t GU,DEsuPPO.TIIl-r LAligning the Blade and Blade Guide Assemblies Model 113.248440Blade Guide 4-20 8 hex washer Head thread forming Screws Mounting FrontTurn front table over. Locate the two 2 latch Springs, two 2 alignment springs, and the fourHead Capscrew Squaring the Blade to the Table Adjusting Front Table ON-OFF Switch Location and function of controlsModel 113.248210 & 113,248320 Adjusting Bevel Lock Knob Operation Recommended Blade Size Basic band saw operationSawdust Collection Circle CuttingInstalling the Sanding Belt Installing Sanding AttachmentMaintenance Adjusting Band SAW Bevel TravelAdjusting the Upper Blade Guide Travel Light Bulb Outlet Before Trouble Shooting Your Band SAW/SANDERRemedy Trouble shooting--motorTrouble Probable CauseTrouble shooting -- electronics ProblemProbable Cause Suggested Corrective Action Trouble shooting ---electronics 113.2485tSuggested Corrective Action Leg Repair partsParts List for Craftsman 12-INCH Band SAW Key Part DescriptionPage Key Drive Assembly PartsModel NOS .248210,113.248320, 113.248440 OMode1113.248320 Only ==Model113.248510 Only Base AssemblyModel NOS .248210,113.248320,113.248440 9414202 Bevel Drive and Motor Mount Assembly PartsScrew, Truss Hd /4-20 x 1/2 Parts List for Craftsman 12-INCH Electronic Band SAWPage Part Numberpartdescription Model Name of Item Airs