Craftsman 113.248510 owner manual Adjusting Front Table

Page 33

ADJUSTING FRONT TABLE

1.Adjust the front table so it is the same height as the rear table as follows:

a, Lay a straight edge across front table to rear table.

b.Gentlytap the fronttable down until it is in line with the rear table,

c.Tighten the Phillips head self tapping screw once the front table is in the correct position.

d.If necessary adjust the two (2) oval point set

screws (see Step 3) as needed to help line up the table.

e.Both the left and right sides of the front table should be adjusted simultaneously.

2, To keep the miter gage grooves in line, use a flat blade screwdriver against the head of one of the low head capscrews in the miter gage groove to force

the table alignment key firmly forward intothe notch in the front table.

3.While holding the alignment key into the notch, tighten theother capscrew. Removethe screwdriver and tighten the remaining screw. Check that the miter gage grooves line up,

4.Check the operation of springs and tabs by remov- ing the front table and reinstalling. Removethetable by lifting up on two spring tabs under front edge of the table until springs are free, then pulling forward.

TABLE LEVELING

SETSCREWS

33

Image 33
Contents Save This Manual For Future Reference 113.248320113.248440113.248510 Table of Contents Keep Work Area Clean Know Your Power Tool Ground ALL ToolsUSE Recommended Accessories Never Stand on Tool Keep Guards in PlaceBefore Using the SAW Additional safety instructions for band sawWhen Installing or Moving the SAW Before Each USEAccessories Before SandingWhenever SAW is Running Glossary of terms for woodworking Power SupplyWire Sizes Motor Safety ProtectionSawdust from interfering with normal motor ventila- tion 25 Ft 26 50 Ft 100 FtGeneral information Unpacking and checking contentsDescription QTY Loose PartsTruss Head Screw 1/4-20x12 List of Loose Parts in BAG #507968List of Loose Parts in BAG #508014 Pan Hd. Screw 10-32 xNuts Support Bracke Leveling Foot Assembly and alignmentModel 113.24821 O Attaching LEG SETDescription Qty Truss Head Assembling Cabinet Model\ ,/o Mounting the SAW to the Cabinet From loose parts bag find the following hardWare Front Attaching the Handwheel Model 113.248210 onlyMounting the Motor Find the following partsModels 113.248440, Tighten Flange NUT After Tensioning Beltwith Wing NUT Steps are Completed Connecting the MotorChanging Speed Settings Recommended Speed SettingsModel 113.248320, 113.248440 Selecting Blade SpeedAttaching Trim Caps MODELS113.248210an¢ Getting to know your band sawOpen Battery Open Location and function of the electronic indicator systemBattery Cover Model 113.248440 & 113.248510 on LYFunction Keys Using the Electronic Indicator SystemRead-out Indicates correct tension for 3000Jrt,t Installing the BladeUpperblade tl t GU,DEsuPPO.TIIl-r LAligning the Blade and Blade Guide Assemblies Model 113.248440Blade Guide Turn front table over. Locate the two 2 latch Mounting FrontSprings, two 2 alignment springs, and the four 4-20 8 hex washer Head thread forming ScrewsHead Capscrew Squaring the Blade to the Table Adjusting Front Table ON-OFF Switch Location and function of controlsModel 113.248210 & 113,248320 Adjusting Bevel Lock Knob Sawdust Collection Basic band saw operationCircle Cutting Operation Recommended Blade SizeInstalling the Sanding Belt Installing Sanding AttachmentMaintenance Adjusting Band SAW Bevel TravelAdjusting the Upper Blade Guide Travel Light Bulb Outlet Before Trouble Shooting Your Band SAW/SANDERTrouble Trouble shooting--motorProbable Cause RemedyTrouble shooting -- electronics ProblemProbable Cause Suggested Corrective Action Trouble shooting ---electronics 113.2485tSuggested Corrective Action Parts List for Craftsman 12-INCH Band SAW Repair partsKey Part Description LegPage Key Drive Assembly PartsModel NOS .248210,113.248320, 113.248440 OMode1113.248320 Only ==Model113.248510 Only Base AssemblyModel NOS .248210,113.248320,113.248440 9414202 Bevel Drive and Motor Mount Assembly PartsScrew, Truss Hd /4-20 x 1/2 Parts List for Craftsman 12-INCH Electronic Band SAWPage Part Numberpartdescription Model Name of Item Airs