Craftsman 113.248510 owner manual Front

Page 16

MODEL 113.248510

2.Place saw on cabinet so that holes in bottom of saw line up with holes in top of cabinet.

3.Install bolts, Iockwashers, and nuts as shown. Tighten securely using a 7/16-inch wrench or socket. The front two bolts hold the saw, lower wheel cover, and the cabinet together. Install these bolts from the bottom side,

4.After the band saw has been mounted to the cabinet, go back and tighten all the nuts that were previously hand tightened using a 7/16- inch wrench or socket.

FRONT

MOUNTING DOOR

Tools needed: 7/16" wrench or socket and phillips screwdriver.

1.Locate the two (2) door hinges and four (4) 10-10 x 1t2 plastite screws. Mount hinges on either side of the door with phillips screwdriver.

2.Locate the four (4) truss head bolts, Iockwasher and hex nuts to attach door hinges to the side panel. Tighten hex nuts with a 7/16" wrench or socket.

3.Locate the magnetic catch, the magnetic catch stop plate, two (2) 6-10 x 1/2 pan head screws and two (2) 6-32 x 3t8 pan head screws. Attach the magnetic catch to the door with the two (2) 6-10 x 1/2 pan head screws using a phillips screwdriver. Attach the mag- netic catch stop plate to the side panel opposite the side the hinges are to be mounted. Use the two (2) 6-32 x 3/8 pan head screws to mount stop plate.

Adjust the stop plate if necessary with phillips screw- driver for desired closure.

;IDE PANEL

MAGNETIC CATCH

STOP PLATE

MAGNETIC

CATCH

16

Image 16
Contents 113.248320 Save This Manual For Future Reference113.248440113.248510 Table of Contents Know Your Power Tool Ground ALL Tools Keep Work Area CleanUSE Recommended Accessories Never Stand on Tool Keep Guards in PlaceAdditional safety instructions for band saw Before Using the SAWWhen Installing or Moving the SAW Before Each USEBefore Sanding AccessoriesWhenever SAW is Running Power Supply Glossary of terms for woodworkingMotor Safety Protection Wire SizesSawdust from interfering with normal motor ventila- tion 25 Ft 26 50 Ft 100 FtUnpacking and checking contents General informationLoose Parts Description QTYList of Loose Parts in BAG #507968 Truss Head Screw 1/4-20x12List of Loose Parts in BAG #508014 Pan Hd. Screw 10-32 xAssembly and alignment Nuts Support Bracke Leveling FootAttaching LEG SET Model 113.24821 ODescription Qty Truss Head Model Assembling Cabinet\ ,/o From loose parts bag find the following hard Mounting the SAW to the CabinetWare Front Model 113.248210 only Attaching the HandwheelMounting the Motor Find the following partsModels 113.248440, Tighten Flange NUT After Tensioning Beltwith Wing NUT Connecting the Motor Steps are CompletedRecommended Speed Settings Changing Speed SettingsModel 113.248320, 113.248440 Selecting Blade SpeedAttaching Trim Caps Getting to know your band saw MODELS113.248210an¢Location and function of the electronic indicator system Open Battery OpenBattery Cover Model 113.248440 & 113.248510 on LYUsing the Electronic Indicator System Function KeysRead-out Indicates correct tension for 3000Installing the Blade Jrt,tGU,DEsuPPO.TIIl-r L Upperblade tl tModel 113.248440 Aligning the Blade and Blade Guide AssembliesBlade Guide Mounting Front Turn front table over. Locate the two 2 latchSprings, two 2 alignment springs, and the four 4-20 8 hex washer Head thread forming ScrewsHead Capscrew Squaring the Blade to the Table Adjusting Front Table Location and function of controls ON-OFF SwitchModel 113.248210 & 113,248320 Adjusting Bevel Lock Knob Basic band saw operation Sawdust CollectionCircle Cutting Operation Recommended Blade SizeInstalling Sanding Attachment Installing the Sanding BeltAdjusting Band SAW Bevel Travel MaintenanceAdjusting the Upper Blade Guide Travel Outlet Before Trouble Shooting Your Band SAW/SANDER Light BulbTrouble shooting--motor TroubleProbable Cause RemedyProblem Trouble shooting -- electronicsProbable Cause Suggested Corrective Action 113.2485t Trouble shooting ---electronicsSuggested Corrective Action Repair parts Parts List for Craftsman 12-INCH Band SAWKey Part Description LegPage Drive Assembly Parts KeyModel NOS .248210,113.248320, 113.248440 Base Assembly OMode1113.248320 Only ==Model113.248510 OnlyModel NOS .248210,113.248320,113.248440 Bevel Drive and Motor Mount Assembly Parts 9414202Parts List for Craftsman 12-INCH Electronic Band SAW Screw, Truss Hd /4-20 x 1/2Page Airs Part Numberpartdescription Model Name of Item