Craftsman 113.248510 owner manual Jrt,t, Installing the Blade

Page 26

ALL MODELS

INSTALLING THE BLADE

WARNING: TO AVOID INJURY FROM ACCIDENTAL STARTING, MAKE SURE THE POWER CORD IS UNPLUGGED BEFORE REMOVING ANY PART FROM THE SAW.

1.Remove the blade guard by loosening the two (2) mounting screws with a phillips screwdriver and lifting the blade guard upward.

2.Loosen the upper blade guide assembly and lower to approximately 3 inches above rear table and retighten lock knob. This is necessary to make adjustments to blade guide and back up roller bearing.

3.Loosen the two capscrews that lock the upper blade guides using a 1/8-inch hex "L,'wrench and separate them about 1/8-inch. Repeat the same step for the lower blade guides.

.IGNUGARD

_.j

LOCK KNOB

Jrt[,t] I

BLADE GUIDE

CAPSCREWS

26

Image 26

Contents 113.248440113.248510 Save This Manual For Future Reference113.248320 Table of Contents USE Recommended Accessories Never Stand on Tool Know Your Power Tool Ground ALL ToolsKeep Work Area Clean Keep Guards in PlaceWhen Installing or Moving the SAW Additional safety instructions for band sawBefore Using the SAW Before Each USEWhenever SAW is Running AccessoriesBefore Sanding Power Supply Glossary of terms for woodworkingSawdust from interfering with normal motor ventila- tion Motor Safety ProtectionWire Sizes 25 Ft 26 50 Ft 100 FtUnpacking and checking contents General informationLoose Parts Description QTYList of Loose Parts in BAG #508014 List of Loose Parts in BAG #507968Truss Head Screw 1/4-20x12 Pan Hd. Screw 10-32 xAssembly and alignment Nuts Support Bracke Leveling FootDescription Qty Truss Head Model 113.24821 OAttaching LEG SET Model Assembling Cabinet\ ,/o Ware Mounting the SAW to the CabinetFrom loose parts bag find the following hard Front Mounting the Motor Model 113.248210 onlyAttaching the Handwheel Find the following partsModels 113.248440, Tighten Flange NUT After Tensioning Beltwith Wing NUT Connecting the Motor Steps are CompletedModel 113.248320, 113.248440 Recommended Speed SettingsChanging Speed Settings Selecting Blade SpeedAttaching Trim Caps Getting to know your band saw MODELS113.248210an¢Battery Cover Location and function of the electronic indicator systemOpen Battery Open Model 113.248440 & 113.248510 on LYRead-out Indicates correct tension for Using the Electronic Indicator SystemFunction Keys 3000Installing the Blade Jrt,tGU,DEsuPPO.TIIl-r L Upperblade tl tModel 113.248440 Aligning the Blade and Blade Guide AssembliesBlade Guide Springs, two 2 alignment springs, and the four Mounting FrontTurn front table over. Locate the two 2 latch 4-20 8 hex washer Head thread forming ScrewsHead Capscrew Squaring the Blade to the Table Adjusting Front Table Model 113.248210 & 113,248320 ON-OFF SwitchLocation and function of controls Adjusting Bevel Lock Knob Circle Cutting Basic band saw operationSawdust Collection Operation Recommended Blade SizeInstalling Sanding Attachment Installing the Sanding BeltAdjusting the Upper Blade Guide Travel MaintenanceAdjusting Band SAW Bevel Travel Outlet Before Trouble Shooting Your Band SAW/SANDER Light BulbProbable Cause Trouble shooting--motorTrouble RemedyProbable Cause Suggested Corrective Action Trouble shooting -- electronicsProblem Suggested Corrective Action Trouble shooting ---electronics113.2485t Key Part Description Repair partsParts List for Craftsman 12-INCH Band SAW LegPage Drive Assembly Parts KeyModel NOS .248210,113.248320, 113.248440 Base Assembly OMode1113.248320 Only ==Model113.248510 OnlyModel NOS .248210,113.248320,113.248440 Bevel Drive and Motor Mount Assembly Parts 9414202Parts List for Craftsman 12-INCH Electronic Band SAW Screw, Truss Hd /4-20 x 1/2Page Airs Part Numberpartdescription Model Name of Item