Craftsman 113.248510 owner manual Connecting the Motor, Steps are Completed

Page 20

ALL MODELS

CONNECTING THE MOTOR

1.Next, the motor cord needs to be wired into the motor. Coming from the underside of the table will be a cord with a black, white and green wire. This is the motor cord.

WARNING: FOR YOUR OWN SAFETY, NEVER PLUG I_HE SAW IN UNTIL ALL ASSEMBLY

STEPS ARE COMPLETED.

2.Loosen the two screws holding the connector box cover on the back side of the motor. Swing the cover open.

3.Install the green ground wire by removing the

green grounding screw and inserting it through the round metal terminal on the green ground wire of the motor cord. Reinstall the green screw into the hole from which it was removed and tighten securely.

WARNING: TO AVOID ELECTROCUTION,

NEVER CONNECT ANYTHING BUT THE

GROUND WIRE (COLORED GREEN) TO THE GREEN SCREW.

4.Insert terminal end of WHITE wire on spade terminal marked T4 on the motor. Push terminal

firmly until seated.

5.Insert terminal end of BLACK wire on spade terminal marked T1 on the motor. Push terminal

firmly until seated.

6.Close motor connector box being sure that power cord is seated in the largest strain relief groove and tighten box cover screws.

7.DQ NOT plug in power cord.

TERMINAL

GREEN

BLACK WIRE

TERMINAL Tt

GREEN WIRE

.TO GREEN SCREW

STRAIN RELIEF

WtRE TO

TERMINAL T4

2O

Image 20
Contents 113.248440113.248510 Save This Manual For Future Reference113.248320 Table of Contents Know Your Power Tool Ground ALL Tools Keep Work Area CleanUSE Recommended Accessories Never Stand on Tool Keep Guards in PlaceAdditional safety instructions for band saw Before Using the SAWWhen Installing or Moving the SAW Before Each USEWhenever SAW is Running AccessoriesBefore Sanding Power Supply Glossary of terms for woodworkingMotor Safety Protection Wire SizesSawdust from interfering with normal motor ventila- tion 25 Ft 26 50 Ft 100 FtUnpacking and checking contents General informationLoose Parts Description QTYList of Loose Parts in BAG #507968 Truss Head Screw 1/4-20x12List of Loose Parts in BAG #508014 Pan Hd. Screw 10-32 xAssembly and alignment Nuts Support Bracke Leveling FootDescription Qty Truss Head Model 113.24821 OAttaching LEG SET Model Assembling Cabinet\ ,/o Ware Mounting the SAW to the CabinetFrom loose parts bag find the following hard Front Model 113.248210 only Attaching the HandwheelMounting the Motor Find the following partsModels 113.248440, Tighten Flange NUT After Tensioning Beltwith Wing NUT Connecting the Motor Steps are CompletedRecommended Speed Settings Changing Speed SettingsModel 113.248320, 113.248440 Selecting Blade SpeedAttaching Trim Caps Getting to know your band saw MODELS113.248210an¢Location and function of the electronic indicator system Open Battery OpenBattery Cover Model 113.248440 & 113.248510 on LYUsing the Electronic Indicator System Function KeysRead-out Indicates correct tension for 3000Installing the Blade Jrt,tGU,DEsuPPO.TIIl-r L Upperblade tl tModel 113.248440 Aligning the Blade and Blade Guide AssembliesBlade Guide Mounting Front Turn front table over. Locate the two 2 latchSprings, two 2 alignment springs, and the four 4-20 8 hex washer Head thread forming ScrewsHead Capscrew Squaring the Blade to the Table Adjusting Front Table Model 113.248210 & 113,248320 ON-OFF SwitchLocation and function of controls Adjusting Bevel Lock Knob Basic band saw operation Sawdust CollectionCircle Cutting Operation Recommended Blade SizeInstalling Sanding Attachment Installing the Sanding BeltAdjusting the Upper Blade Guide Travel MaintenanceAdjusting Band SAW Bevel Travel Outlet Before Trouble Shooting Your Band SAW/SANDER Light BulbTrouble shooting--motor TroubleProbable Cause RemedyProbable Cause Suggested Corrective Action Trouble shooting -- electronicsProblem Suggested Corrective Action Trouble shooting ---electronics113.2485t Repair parts Parts List for Craftsman 12-INCH Band SAWKey Part Description LegPage Drive Assembly Parts KeyModel NOS .248210,113.248320, 113.248440 Base Assembly OMode1113.248320 Only ==Model113.248510 OnlyModel NOS .248210,113.248320,113.248440 Bevel Drive and Motor Mount Assembly Parts 9414202Parts List for Craftsman 12-INCH Electronic Band SAW Screw, Truss Hd /4-20 x 1/2Page Airs Part Numberpartdescription Model Name of Item