Craftsman 113.248510 owner manual Installing Sanding Attachment, Installing the Sanding Belt

Page 37

INSTALLING SANDING ATTACHMENT

WARNING: TO AVOID INJURY FROM UNEXPECTED

STARTING, MAKE SURE POWER CORD IS UNPLUG-

GED BEFORE MAKING ADJUSTMENTS TO BAND-

SAW PARTS.

NOTE: The sanding bett cuts very rapidly. Practice with some scraps of wood first before you attempt to sand your actual workpiece.

1.To install the sanding belt and sanding platen, remove the front table, front cover, blade guard, and the blade.

2.Use a 1/8-inch hex "L" wrench and remove the upper and lower right blade guides. The mount- ing screw used for the upper blade guide will be used to hold the sanding platen in place.

3.Loosen the setscrews that hold the upper and lower backup bearings in place and push the bearings all the way back_ Tighten setscrews so bearings will remain.

4.Slide the sanding platen into the blade slot in the table and fasten to the upper blade guide

assembly where the right blade guide mounts. It may be necessary to loosen the left blade guide and slide it backwards until platen is in place.

5, Slide the upper left blade guide towards the sanding platen and tighten mounting screw securely.

6.Slide the lower teft blade guide towards the sanding platen until the platen rests 1/8-inch away from the right edge of the slot in the work table,

SANDING PLATEN

INSTALLING THE SANDING BELT

1.Install the sanding belt and adjust tension to the sanding position. (The letter "S" on the scale.)

2.Rotate the upper wheel by hand (clockwise) to check the sanding belt tracking. Adjust tracking if necessary. (Reference the blade tracking sec- tion for tracking procedure.)

3.After tracking the sanding belt if the belt and the platen do not align loosen the upper blade guide support and slide the support in or out to align. Then tighten set screws to hold support and platen in place, it may also be necessary to adjust the lower blade guide support to align the blade guide with the sanding platen.

NOTE: A new sanding belt will stretch with use, so check the tension often.

,Ii I ' %

. i_ii

SANDING

BELT

!1-'2

Image 37
Contents 113.248320 Save This Manual For Future Reference113.248440113.248510 Table of Contents Keep Work Area Clean Know Your Power Tool Ground ALL ToolsUSE Recommended Accessories Never Stand on Tool Keep Guards in PlaceBefore Using the SAW Additional safety instructions for band sawWhen Installing or Moving the SAW Before Each USEBefore Sanding AccessoriesWhenever SAW is Running Glossary of terms for woodworking Power SupplyWire Sizes Motor Safety ProtectionSawdust from interfering with normal motor ventila- tion 25 Ft 26 50 Ft 100 FtGeneral information Unpacking and checking contentsDescription QTY Loose PartsTruss Head Screw 1/4-20x12 List of Loose Parts in BAG #507968List of Loose Parts in BAG #508014 Pan Hd. Screw 10-32 xNuts Support Bracke Leveling Foot Assembly and alignmentAttaching LEG SET Model 113.24821 ODescription Qty Truss Head Assembling Cabinet Model\ ,/o From loose parts bag find the following hard Mounting the SAW to the CabinetWare Front Attaching the Handwheel Model 113.248210 onlyMounting the Motor Find the following partsModels 113.248440, Tighten Flange NUT After Tensioning Beltwith Wing NUT Steps are Completed Connecting the MotorChanging Speed Settings Recommended Speed SettingsModel 113.248320, 113.248440 Selecting Blade SpeedAttaching Trim Caps MODELS113.248210an¢ Getting to know your band sawOpen Battery Open Location and function of the electronic indicator systemBattery Cover Model 113.248440 & 113.248510 on LYFunction Keys Using the Electronic Indicator SystemRead-out Indicates correct tension for 3000Jrt,t Installing the BladeUpperblade tl t GU,DEsuPPO.TIIl-r LAligning the Blade and Blade Guide Assemblies Model 113.248440Blade Guide Turn front table over. Locate the two 2 latch Mounting FrontSprings, two 2 alignment springs, and the four 4-20 8 hex washer Head thread forming ScrewsHead Capscrew Squaring the Blade to the Table Adjusting Front Table Location and function of controls ON-OFF SwitchModel 113.248210 & 113,248320 Adjusting Bevel Lock Knob Sawdust Collection Basic band saw operationCircle Cutting Operation Recommended Blade SizeInstalling the Sanding Belt Installing Sanding AttachmentAdjusting Band SAW Bevel Travel MaintenanceAdjusting the Upper Blade Guide Travel Light Bulb Outlet Before Trouble Shooting Your Band SAW/SANDERTrouble Trouble shooting--motorProbable Cause RemedyProblem Trouble shooting -- electronicsProbable Cause Suggested Corrective Action 113.2485t Trouble shooting ---electronicsSuggested Corrective Action Parts List for Craftsman 12-INCH Band SAW Repair partsKey Part Description LegPage Key Drive Assembly PartsModel NOS .248210,113.248320, 113.248440 OMode1113.248320 Only ==Model113.248510 Only Base AssemblyModel NOS .248210,113.248320,113.248440 9414202 Bevel Drive and Motor Mount Assembly PartsScrew, Truss Hd /4-20 x 1/2 Parts List for Craftsman 12-INCH Electronic Band SAWPage Part Numberpartdescription Model Name of Item Airs