DeWalt DWD460K Speed Selector Fig, Trigger Switch Fig, Forward/Reverse Button Fig, Operation

Page 9

The two position side handle (I) can be assembled into either side of tool. Thread the side handle (I) into the bail handle bolt (E) or directly into threaded holes (J) on desired side. Tighten securely by hand.

FIG. 5

A

I

E

J

Speed Selector (Fig. 1)

NOTICE: Risk of tool damage. Do not rotate the speed selector lever while the drill is running or coasting, damage may occur to the tool. Rotate the speed selector lever (B) to the desired speed:

1= low speed (330 RPM)

2 = high speed (1300 RPM)

NOTE: The first time the tool is run after changing speeds, you may hear a click on start up. This is normal and does not indicate a problem.

Trigger Switch (Fig. 1)

Depressing the trigger switch (D) turns the tool on, releasing the trigger switch turns the tool off.

VARIABLE SPEED

A variable speed trigger switch permits speed control—the farther the trigger is depressed, the higher the speed of the drill.

NOTE: Use lower speeds for starting holes without a center punch, drilling in metal, plastics or ceramics. Higher speeds are better for drilling wood and composition boards.

Forward/Reverse Button (Fig. 1)

A forward/reverse button (C) determines the direction of the tool. It is located in front of the trigger switch.

To select forward rotation, release the trigger switch (D) and depress the forward/reverse button on the right side of the tool.

To select reverse, depress the forward/reverse button on the left side of the tool. When changing the position of the button, be sure the trigger is released.

NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on start up. This is normal and does not indicate a problem.

OPERATION

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

The bit rotates clockwise when the tool is in the forward position and counterclockwise when the tool is in the reverse position. If the bit binds, the tool will slow to a manageable level. Using proper hand position, brace the side handle (I) or tool body against a stud for better support (Fig. 3).

English

7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents DWD450, DWD460 Page General Power Tool Safety Warnings Definitions Safety GuidelinesWork Area Safety Electrical SafetyPersonal Safety Power Tool USE and CareService AWG Additional Specific Safety InstructionsMotor For Future USEComponents Intended USEAssembly and Adjustments TorqueBracing the Tool Bail Handle Fig Indicator Diagnosis SolutionSide Handle Fig Slip ClutchSpeed Selector Fig Trigger Switch FigForward/Reverse Button Fig OperationChuck Key Holder , 7 DrillingKeyed Chuck Drilling in MetalCleaning Accessories MaintenanceMotor Brushes LubricationThree Year Limited Warranty RepairsRegister Online English Définitions lignes directrices en Matière de sécurité Sécurité DU Lieu DE TravailSécurité EN Matière D’ÉLECTRICITÉ Utilisation ET Entretien D’UN Outil Électrique Sécurité PersonnelleRéparation Consignes de sécurité particulières additionnelles240 Moteur Conserver CES Consignes Pour Utilisation UltérieureDescription Usage PrévuAssemblage ET Ajustements CouplePréhension DE L’OUTIL Voyant Diagnostic Solution Limiteur DE Couple À FrictionCLUTCHMDDWD460 Poignée latérale Fig Poignée étrier FigSélecteur de vitesse Fig Gâchette FigUtilisation Bouton marche avant/arrière FigPerçage Vitesse VariableMandrin à clé Sangle de la clé de mandrin , 7Balais de moteur AccessoiresLubrification NettoyageRéparations Capacités Maximales RecommandéesRegistre en ligne Garantie limitée de trois ansGarantie DE Remboursement DE 90 Jours Contrat D’ENTRETIEN Gratuit D’UN ANDefiniciones Normas de seguridad Seguridad EN EL Área DE TrabajoSeguridad Eléctrica USO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalMantenimiento Instrucciones Específicas de Seguridad AdicionalesCalibre mínimo para cables de alimentación Guarde Estas Instrucciones Para Futuras Consultas ComponentesAplicación Montaje Y Ajustes TorsorSujetando LA Herramienta Mango lateral Fig Indicador Diagnostico SoluciónEmbrague Deslizable Embrague E-CLUTCHTMDWD460Conmutador tipo gatillo Fig Palanca de Selección de Velocidad FigOperación Botón de avance/reverso FigTaladrado Velocidad VariablePortabrocas con Llave Sujetador de la Llave del Portabrocas , 7Taladrado EN Metal Taladrado EN MaderaEscobillas del Motor MantenimientoLubricación LimpiezaReparaciones Registro en línea Póliza de GarantíaGarantía limitada por tres años Para Otras LocalidadesAÑO DE Servicio Gratuito Garantía DE Reembolso DE SU Dinero POR 90 DíasEspecificacións Page Page Page Copyright 2008, 2013, 2014 D Ewalt
Top Page Image Contents