Grizzly G0634Z manual Safety Labels and Cosmetic Parts

Page 15

Safety Labels and Cosmetic Parts

806

803

800
		807
801	808	805
	808
802		804

813

809

810

811

812

REF	PART #	DESCRIPTION

800	PLABEL-12	READ MANUAL 2" X 3 5/16"
801	PLABEL-37	RESPIRATOR/GLASSES LABEL
802	P0634Z802	MACHINE ID LABEL G0634Z
803	P0633803	CUTTERHEAD GUARD WARNING
804	PLABEL-15	EAR PROTECTION 2"X3 5/16"H
805	P0633805	DISCONNECT POWER LABEL
806	P0633806	CHANGING OPERATIONS WARNING

REF	PART #	DESCRIPTION

807	PPAINT-1	GRIZZLY GREEN PAINT
808	PPAINT-11	GREY PUTTY TOUCH UP PAINT
809	PLABEL-14	ELECTRICITY LABEL
810	P0634Z810	MODEL NUMBER LABEL G0634Z
811	P0633811	TABLE LOCK KNOB NOTICE
812	P0633812	CHANGE LEVER NOTICE
813	G8588	GRIZZLY NAMEPLATE-SMALL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

Model G0634Z Manual Insert (Mfg. 5/09+)

-15-

Image 15

Contents G0634Z only Figure Machine InventoryReplacing Carbide Inserts G0634Z Tools Needed QtyTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Planer Stand Assembly Description Stand Parts ListTable Assembly Cutterhead & Motor Description Cutterhead & Motor Parts ListDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard PR01M EXT Retaining Ring 10MM Fence/Guard Parts ListSafety Labels and Cosmetic Parts Accessories H4978 T20446 H4979H9893-Carbide Inserts 10 Pack JOINTER/PLANER Combination Machine Page Table of Contents Contact Info ForewordG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0634 identification and controls IdentificationG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Plug/Receptacle Type Grounding 220V OperationAmperage Draw Circuit RequirementsDescription Qty Set Up SafetyItems Needed for Setup UnpackingG0634 only Figure Common Components Qty Jointer/Planer Assembly Not shownInventory G0633 only FigureHardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsFront and right rear lifting hole Locations Moving & Placing Base UnitTo set the outfeed table height Setting Outfeed Table HeightTo install the cutterhead guard Cutterhead GuardKnife Setting Gauge Dust CollectionTo connect a dust collection hose To test run the machine Test RunTighten V-Belts Recommended AdjustmentsOperations Operation SafetyPage To set up the machine for planer operations Basic Planer ControlsJointer-Planer Conversion Planer dust port in down position To change the machine for jointer opera- tionsCorrect and incorrect grain alignment To cutterhead jointer Stock Inspection and RequirementsThickness Planer Specific Rules Squaring StockTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingBasic steps of operating the planer are as follows Basic Planer OperationAccessories H4979 H4977 H1302Cleaning ScheduleBelts Roller chains LubricationPage Troubleshooting Motor & ElectricalTable Jointer 43 or Cutting Jointer and PlanerChecking Outfeed Table Parallelism Checking/Adjusting Jointer Table ParallelismCorrecting Outfeed Table to Cutterhead Parallelism Checking Infeed Table ParallelismTo correct outfeed table parallelism Adjusting Jointer Table Parallelism To adjust the jointer table parallelismInfeed Table to Cutterhead Parallelism on To inspect the knives with the knife setting gauge Inspecting Knives G0633 OnlyTo inspect the knives with a straightedge Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To align the pulleys Calibrating Depth ScalePulley Alignment To calibrate the depth scaleTo set the 90˚ fence stop Setting Fence StopsAdjusting Table Lock Levers To adjust the table lock leversTo set the 45 fence stop To adjust the table gibs Adjusting GibsTable Parallelism Inspection Table Parallelism AdjustmentsTo adjust the table parallelism Planer Table ParallelismSpring Tension To adjust feed roller spring tensionAnti-Kickback Fingers Electrical Components G0633/G0634 magnetic switchWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List PR01M EXT Retaining Ring 10MM Fence/Guard List801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page