Grizzly G0634Z manual Accessories, H4978 T20446 H4979, H9893-Carbide Inserts 10 Pack

Page 16

Accessories

H4978—Deluxe Earmuffs - 27dB

H4979—Twin Cup Hearing Protector - 29dB

T20446—Ear Plugs 200 Pair - 31dB

Protect your hearing before its too late. Especially important if you or employees operate for hours at a time.

H4978

T20446

H4979

Figure 4. Hearing protection assortment.

T20501—Face Shield Crown Protector 4"

T20502—Face Shield Crown Protector 7"

T20503—Face Shield Window

T20452—"Kirova" Anti-Reflective S. Glasses

T20451—"Kirova" Clear Safety Glasses

H0736—Shop Fox® Safety Glasses

H7194—Bifocal Safety Glasses 1.5

H7195—Bifocal Safety Glasses 2.0

H7196—Bifocal Safety Glasses 2.5

T20502

 

T20452

 

 

 

T20503

T20451

H7194

 

H0736

Figure 5. Eye protection assortment.

H9893—Carbide Inserts (10 Pack)

These indexable carbide inserts can be rotated to provide four factory sharp edges before replace- ment.

Figure 6. H9893 carbide inserts.

G9256—6" Dial Caliper

G9257—8" Dial Caliper

G9258—12" Dial Caliper

Essential for planing, jointing, or sanding to criti- cal tolerances. These traditional dial calipers are accurate to 0.001" and can measure outside surfaces, inside surfaces, and heights/depths. Features stainless steel, shock resistant construc- tion and a dust proof display. An absolute treat for the perfectionist!

Figure 7. Grizzly® Dial Calipers.

-16-

Model G0634Z Manual Insert (Mfg. 5/09+)

Image 16
Contents Machine Inventory G0634Z only FigureTools Needed Qty Replacing Carbide Inserts G0634ZTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Planer Stand Assembly Stand Parts List DescriptionTable Assembly Cutterhead & Motor Cutterhead & Motor Parts List DescriptionDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard Fence/Guard Parts List PR01M EXT Retaining Ring 10MMSafety Labels and Cosmetic Parts H4978 T20446 H4979 AccessoriesH9893-Carbide Inserts 10 Pack JOINTER/PLANER Combination Machine Page Table of Contents Foreword Contact InfoG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controlsG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers 220V Operation Amperage DrawCircuit Requirements Plug/Receptacle Type GroundingSet Up Safety Items Needed for SetupUnpacking Description QtyCommon Components Qty Jointer/Planer Assembly Not shown InventoryG0633 only Figure G0634 only FigureHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadMoving & Placing Base Unit Front and right rear lifting hole LocationsSetting Outfeed Table Height To install the cutterhead guardCutterhead Guard To set the outfeed table heightDust Collection Knife Setting GaugeTo connect a dust collection hose Test Run To test run the machineRecommended Adjustments Tighten V-BeltsOperation Safety OperationsPage Basic Planer Controls To set up the machine for planer operationsJointer-Planer Conversion To change the machine for jointer opera- tions Planer dust port in down positionStock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointerSquaring Stock Thickness Planer Specific RulesSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerBasic Planer Operation Basic steps of operating the planer are as followsAccessories H1302 H4979 H4977Schedule CleaningBelts Lubrication Roller chainsPage Motor & Electrical TroubleshootingTable Jointer Cutting Jointer and Planer 43 orChecking/Adjusting Jointer Table Parallelism Checking Outfeed Table ParallelismChecking Infeed Table Parallelism Correcting Outfeed Table to Cutterhead ParallelismTo correct outfeed table parallelism To adjust the jointer table parallelism Adjusting Jointer Table ParallelismInfeed Table to Cutterhead Parallelism on Inspecting Knives G0633 Only To inspect the knives with the knife setting gaugeTo inspect the knives with a straightedge Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 Calibrating Depth Scale Pulley AlignmentTo calibrate the depth scale To align the pulleysSetting Fence Stops To set the 90˚ fence stopTo adjust the table lock levers Adjusting Table Lock LeversTo set the 45 fence stop Adjusting Gibs To adjust the table gibsTable Parallelism Adjustments To adjust the table parallelismPlaner Table Parallelism Table Parallelism InspectionTo adjust feed roller spring tension Spring TensionAnti-Kickback Fingers G0633/G0634 magnetic switch Electrical ComponentsWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MM801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page