Grizzly G0634Z manual

Page 54

Lead Screw: The lead screw should be lubri- cated with multi-purpose grease once a month. See Figure 50 and Parts Beakdown, P0633411, Page 61 for location. Remove the left side access panel for ingress.

Lead

Screw

Planer

Column

Figure 50. Planer column and lead screw.

Planer Column: Clean with solvent, wipe dry, and relubricate with multi-purpose grease when needed.

Worm Gear: Inspect every six months and lubri- cate with multi-purpose grease when needed (see Parts Breakdown, P0633409). Remove the worm gear box (see P0633407, Page 61) to inspect.

-36-

Fence: Lubricate with multi-purpose grease when needed in the locations shown in Figure 51.

Figure 51. Fence lubrication locations.

G0633/G0634 Jointer/Planer Combo Machine

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Machine Inventory G0634Z only FigureReplacing Carbide Inserts G0634Z Tools Needed QtyTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Planer Stand Assembly Stand Parts List DescriptionTable Assembly Cutterhead & Motor Cutterhead & Motor Parts List DescriptionDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard Fence/Guard Parts List PR01M EXT Retaining Ring 10MMSafety Labels and Cosmetic Parts Accessories H4978 T20446 H4979H9893-Carbide Inserts 10 Pack JOINTER/PLANER Combination Machine Page Table of Contents Foreword Contact InfoG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controlsG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Circuit Requirements 220V OperationAmperage Draw Plug/Receptacle Type GroundingUnpacking Set Up SafetyItems Needed for Setup Description QtyG0633 only Figure Common Components Qty Jointer/Planer Assembly Not shownInventory G0634 only FigureHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadMoving & Placing Base Unit Front and right rear lifting hole LocationsCutterhead Guard Setting Outfeed Table HeightTo install the cutterhead guard To set the outfeed table heightKnife Setting Gauge Dust CollectionTo connect a dust collection hose Test Run To test run the machineRecommended Adjustments Tighten V-BeltsOperation Safety OperationsPage To set up the machine for planer operations Basic Planer ControlsJointer-Planer Conversion To change the machine for jointer opera- tions Planer dust port in down positionStock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointerSquaring Stock Thickness Planer Specific RulesSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerBasic Planer Operation Basic steps of operating the planer are as followsAccessories H1302 H4979 H4977Cleaning ScheduleBelts Lubrication Roller chainsPage Troubleshooting Motor & ElectricalTable Jointer Cutting Jointer and Planer 43 orChecking/Adjusting Jointer Table Parallelism Checking Outfeed Table ParallelismCorrecting Outfeed Table to Cutterhead Parallelism Checking Infeed Table ParallelismTo correct outfeed table parallelism Adjusting Jointer Table Parallelism To adjust the jointer table parallelismInfeed Table to Cutterhead Parallelism on To inspect the knives with the knife setting gauge Inspecting Knives G0633 OnlyTo inspect the knives with a straightedge Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To calibrate the depth scale Calibrating Depth ScalePulley Alignment To align the pulleysSetting Fence Stops To set the 90˚ fence stopAdjusting Table Lock Levers To adjust the table lock leversTo set the 45 fence stop Adjusting Gibs To adjust the table gibsPlaner Table Parallelism Table Parallelism AdjustmentsTo adjust the table parallelism Table Parallelism InspectionTo adjust feed roller spring tension Spring TensionAnti-Kickback Fingers G0633/G0634 magnetic switch Electrical ComponentsWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MM801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page
Top Page Image Contents