Grizzly G0634Z manual Moving & Placing Base Unit, Front and right rear lifting hole Locations

Page 35

Moving & Placing

Base Unit

The Model G0633/G0634 is

aheavy machine. Serious personal injury may occur if safe moving methods are not used. To be safe, get assistance and use

power equipment to move the shipping crate and remove the machine from the crate.

Unbolt the jointer/planer from the pallet, and use a forklift to lift the machine off the pallet and onto a suitable location as shown in Figure 8. Only lift the machine enough to clear the floor.

Figure 8. Lifting model G0633 with a forklift.

You can also attach hooks and lifting straps to the machine using the three lifting holes shown in Figures 9 & 10 with a forklift, hoist, or boom crane. If you choose this alternative, you must punch out the lifting strap holes—this will perma- nently alter your machine.

If you are unsure how to lift this machine, consult a qualified professional.

After setting the machine in place, remove the shipping brackets on both sides (Figure 9).

G0633/G0634 Jointer/Planer Combo Machine

Brackets

Figure 9. Front and right rear lifting hole

locations.

Figure 10. Left rear lifting hole location.

-17-

Image 35

Contents G0634Z only Figure Machine InventoryTo rotate or change a carbide insert Replacing Carbide Inserts G0634ZTools Needed Qty Machine Data Sheet Cutting Capacities Planer Stand Assembly Description Stand Parts ListTable Assembly Cutterhead & Motor Description Cutterhead & Motor Parts ListDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard PR01M EXT Retaining Ring 10MM Fence/Guard Parts ListSafety Labels and Cosmetic Parts H9893-Carbide Inserts 10 Pack AccessoriesH4978 T20446 H4979 JOINTER/PLANER Combination Machine Page Table of Contents Contact Info ForewordG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0634 identification and controls IdentificationG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Plug/Receptacle Type Grounding 220V OperationAmperage Draw Circuit RequirementsDescription Qty Set Up SafetyItems Needed for Setup UnpackingG0634 only Figure Common Components Qty Jointer/Planer Assembly Not shownInventory G0633 only FigureHardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsFront and right rear lifting hole Locations Moving & Placing Base UnitTo set the outfeed table height Setting Outfeed Table HeightTo install the cutterhead guard Cutterhead GuardTo connect a dust collection hose Knife Setting GaugeDust Collection To test run the machine Test RunTighten V-Belts Recommended AdjustmentsOperations Operation SafetyPage Jointer-Planer Conversion To set up the machine for planer operationsBasic Planer Controls Planer dust port in down position To change the machine for jointer opera- tionsCorrect and incorrect grain alignment To cutterhead jointer Stock Inspection and RequirementsThickness Planer Specific Rules Squaring StockTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingBasic steps of operating the planer are as follows Basic Planer OperationAccessories H4979 H4977 H1302Belts CleaningSchedule Roller chains LubricationPage Table Jointer TroubleshootingMotor & Electrical 43 or Cutting Jointer and PlanerChecking Outfeed Table Parallelism Checking/Adjusting Jointer Table ParallelismTo correct outfeed table parallelism Correcting Outfeed Table to Cutterhead ParallelismChecking Infeed Table Parallelism Infeed Table to Cutterhead Parallelism on Adjusting Jointer Table ParallelismTo adjust the jointer table parallelism To inspect the knives with a straightedge To inspect the knives with the knife setting gaugeInspecting Knives G0633 Only Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To align the pulleys Calibrating Depth ScalePulley Alignment To calibrate the depth scaleTo set the 90˚ fence stop Setting Fence StopsTo set the 45 fence stop Adjusting Table Lock LeversTo adjust the table lock levers To adjust the table gibs Adjusting GibsTable Parallelism Inspection Table Parallelism AdjustmentsTo adjust the table parallelism Planer Table ParallelismSpring Tension To adjust feed roller spring tensionAnti-Kickback Fingers Electrical Components G0633/G0634 magnetic switchWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List PR01M EXT Retaining Ring 10MM Fence/Guard List801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page