Grizzly G0634Z manual Table of Contents

Page 19

Table of Contents

INTRODUCTION	2
Foreword	2
Contact Info	2
G0633 Machine Data Sheet	3
G0634 Machine Data Sheet	5
Identification	7
SECTION 1: SAFETY	8
Safety Instructions for Machinery	8
Additional Safety Instructions for Jointers ...	10
Additional Safety Instructions for Planers....	11
SECTION 2: CIRCUIT REQUIREMENTS	12
220V Operation	12
SECTION 3: SET UP	13
Set Up Safety	13
Items Needed for Setup	13
Unpacking	13
Inventory	14
Hardware Recognition Chart	15
Clean Up	16
Site Considerations	16
Moving & Placing Base Unit	17
Setting Outfeed Table Height	18
Cutterhead Guard	18
Knife Setting Gauge	19
Dust Collection	19
Test Run	20
Recommended Adjustments	21
Tighten V-Belts	21
SECTION 4: OPERATIONS	22
Operation Safety	22
Basic Jointer Controls	22
Basic Planer Controls	24
Jointer-Planer Conversion	24
Stock Inspection and Requirements	26
Squaring Stock	27
Surface Planing	28
Edge Jointing	29
Bevel Cutting	30
Basic Planer Operation	31

SECTION 5: ACCESSORIES	32
SECTION 6: MAINTENANCE	34
Schedule	34
Cleaning	34
V-Belts	34
Lubrication	35
SECTION 7: SERVICE	37
Troubleshooting	37
Checking/Adjusting Jointer Table Parallelism..
39
Inspecting Knives (G0633 Only)	42
Adjusting/Replacing Knives (G0633)	43
Replacing Carbide Inserts (G0634)	45
Calibrating Depth Scale	46
Pulley Alignment	46
Setting Fence Stops	47
Adjusting Table Lock Levers	48
Adjusting Gibs	49
Planer Table Parallelism	50
Spring Tension	51
Anti-Kickback Fingers	52
Electrical Components	53
Wiring Diagram	54
Stand Assembly Parts Breakdown	55
Stand Parts List	56
Table Assembly Parts Breakdown & List ....	57
Cutterhead & Motor Breakdown	58
Cutterhead & Motor Parts List	59
Drive Assembly Breakdown & List	60
Planer Table Breakdown & List	61
Limit Switch Breakdown & List	62
Fence/Guard Breakdown & List	63
Fence/Guard List	64
Safety Labels and Cosmetic Parts	65
WARRANTY AND RETURNS	66

Image 19

Contents G0634Z only Figure Machine InventoryTools Needed Qty Replacing Carbide Inserts G0634ZTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Planer Stand Assembly Description Stand Parts ListTable Assembly Cutterhead & Motor Description Cutterhead & Motor Parts ListDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard PR01M EXT Retaining Ring 10MM Fence/Guard Parts ListSafety Labels and Cosmetic Parts H4978 T20446 H4979 AccessoriesH9893-Carbide Inserts 10 Pack JOINTER/PLANER Combination Machine Page Table of Contents Contact Info ForewordG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0634 identification and controls IdentificationG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Plug/Receptacle Type Grounding 220V OperationAmperage Draw Circuit RequirementsDescription Qty Set Up SafetyItems Needed for Setup UnpackingG0634 only Figure Common Components Qty Jointer/Planer Assembly Not shownInventory G0633 only FigureHardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsFront and right rear lifting hole Locations Moving & Placing Base UnitTo set the outfeed table height Setting Outfeed Table HeightTo install the cutterhead guard Cutterhead GuardDust Collection Knife Setting GaugeTo connect a dust collection hose To test run the machine Test RunTighten V-Belts Recommended AdjustmentsOperations Operation SafetyPage Basic Planer Controls To set up the machine for planer operationsJointer-Planer Conversion Planer dust port in down position To change the machine for jointer opera- tionsCorrect and incorrect grain alignment To cutterhead jointer Stock Inspection and RequirementsThickness Planer Specific Rules Squaring StockTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingBasic steps of operating the planer are as follows Basic Planer OperationAccessories H4979 H4977 H1302Schedule CleaningBelts Roller chains LubricationPage Motor & Electrical TroubleshootingTable Jointer 43 or Cutting Jointer and PlanerChecking Outfeed Table Parallelism Checking/Adjusting Jointer Table ParallelismChecking Infeed Table Parallelism Correcting Outfeed Table to Cutterhead ParallelismTo correct outfeed table parallelism To adjust the jointer table parallelism Adjusting Jointer Table ParallelismInfeed Table to Cutterhead Parallelism on Inspecting Knives G0633 Only To inspect the knives with the knife setting gaugeTo inspect the knives with a straightedge Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To align the pulleys Calibrating Depth ScalePulley Alignment To calibrate the depth scaleTo set the 90˚ fence stop Setting Fence StopsTo adjust the table lock levers Adjusting Table Lock LeversTo set the 45 fence stop To adjust the table gibs Adjusting GibsTable Parallelism Inspection Table Parallelism AdjustmentsTo adjust the table parallelism Planer Table ParallelismSpring Tension To adjust feed roller spring tensionAnti-Kickback Fingers Electrical Components G0633/G0634 magnetic switchWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List PR01M EXT Retaining Ring 10MM Fence/Guard List801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page