Grizzly G0634Z manual Setting Fence Stops, To set the 90˚ fence stop

Page 65

	��
��	��
	��

��	��
	��

��

Figure 69. Pulleys properly aligned. V-belts are

parallel and coplaner.

—If the pulleys are aligned, then no adjust- ments are necessary.

—If the pulleys are NOT aligned, perform Steps 3 & 4.

3.Remove the V-belts (see Page 34), loosen the set screws on the end of the cutterhead pulley, and align the cutterhead pulley with the motor pulley.

4.Tighten the set screws, replace the V-belts, and repeat Step 2.

5.Reinstall the V-belt cover, fence bracket and fence assembly.

Setting Fence Stops

The fence stops simplify the task of adjusting the fence to 45˚ and 90˚.

Tools Needed	Qty
45° Square	1
90° Square	1
Sliding Bevel	1
Wrench 10mm	1
To set the 90˚ fence stop:

1.Loosen the lock nut on the 90° fence stop bolt shown in Figure 70, and loosen the fence tilt lock.

2.Place a 90° square against the table and fence, and adust the stop bolt, so the fence is set exactly at 90°.

Lock Nut

	90˚Stop Bolt

	Figure 70. Adjusting fence to 90˚.
3.	Tighten the lock nut.
4.	Adjust the indicator (if necessary) to 0° to
	calibrate the fence tilt scale.

G0633/G0634 Jointer/Planer Combo Machine

-47-

Image 65

Contents G0634Z only Figure Machine InventoryTo rotate or change a carbide insert Replacing Carbide Inserts G0634ZTools Needed Qty Machine Data Sheet Cutting Capacities Planer Stand Assembly Description Stand Parts ListTable Assembly Cutterhead & Motor Description Cutterhead & Motor Parts ListDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard PR01M EXT Retaining Ring 10MM Fence/Guard Parts ListSafety Labels and Cosmetic Parts H9893-Carbide Inserts 10 Pack AccessoriesH4978 T20446 H4979 JOINTER/PLANER Combination Machine Page Table of Contents Contact Info ForewordG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0634 identification and controls IdentificationG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Amperage Draw 220V OperationCircuit Requirements Plug/Receptacle Type GroundingItems Needed for Setup Set Up SafetyUnpacking Description QtyInventory Common Components Qty Jointer/Planer Assembly Not shownG0633 only Figure G0634 only FigureHardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadFront and right rear lifting hole Locations Moving & Placing Base UnitTo install the cutterhead guard Setting Outfeed Table HeightCutterhead Guard To set the outfeed table heightTo connect a dust collection hose Knife Setting GaugeDust Collection To test run the machine Test RunTighten V-Belts Recommended AdjustmentsOperations Operation SafetyPage Jointer-Planer Conversion To set up the machine for planer operationsBasic Planer Controls Planer dust port in down position To change the machine for jointer opera- tionsCorrect and incorrect grain alignment To cutterhead jointer Stock Inspection and RequirementsThickness Planer Specific Rules Squaring StockTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingBasic steps of operating the planer are as follows Basic Planer OperationAccessories H4979 H4977 H1302Belts CleaningSchedule Roller chains LubricationPage Table Jointer TroubleshootingMotor & Electrical 43 or Cutting Jointer and PlanerChecking Outfeed Table Parallelism Checking/Adjusting Jointer Table ParallelismTo correct outfeed table parallelism Correcting Outfeed Table to Cutterhead ParallelismChecking Infeed Table Parallelism Infeed Table to Cutterhead Parallelism on Adjusting Jointer Table ParallelismTo adjust the jointer table parallelism To inspect the knives with a straightedge To inspect the knives with the knife setting gaugeInspecting Knives G0633 Only Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 Pulley Alignment Calibrating Depth ScaleTo calibrate the depth scale To align the pulleysTo set the 90˚ fence stop Setting Fence StopsTo set the 45 fence stop Adjusting Table Lock LeversTo adjust the table lock levers To adjust the table gibs Adjusting GibsTo adjust the table parallelism Table Parallelism AdjustmentsPlaner Table Parallelism Table Parallelism InspectionSpring Tension To adjust feed roller spring tensionAnti-Kickback Fingers Electrical Components G0633/G0634 magnetic switchWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List PR01M EXT Retaining Ring 10MM Fence/Guard List801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page