Grizzly G0634Z manual Additional Safety Instructions for Jointers

Page 28

Additional Safety Instructions for Jointers

1.JOINTER KICKBACK. "Kickback" is when the workpiece is thrown off the jointer table by the force of the cutterhead. Always use push blocks and safety glasses to reduce the likelihood of injury from “kickback.” If you do not understand what kickback is, or how it occurs, DO NOT operate this machine.

2.CUTTERHEAD ALIGNMENT. Keep the top edge of the outfeed table aligned with the cutterhead knife or insert at top dead center (TDC) to avoid kickback and personal inju- ries.

3.PUSH BLOCKS. Always use push blocks whenever surface planing. Never pass your hands directly over the cutterhead without a push block.

4.WORKPIECE SUPPORT. Supporting the workpiece adequately at all times while cutting is crucial for making safe cuts and avoiding injury. Never attempt to make a cut with an unstable workpiece.

5.KICKBACK ZONE. The "kickback zone" is the path directly through the end of the infeed table. Never stand or allow others to stand in this area during operation.

6.MAXIMUM CUTTING DEPTH. The maxi- mum cutting depth for one pass is 18". Never attempt any single cut deeper than this!

7.JOINTING WITH THE GRAIN. Jointing against the grain or jointing end grain is dangerous and could produce chatter or excessive chip out. Always joint with the grain.

8.KEEPING GUARDS IN PLACE. With the exception of rabbeting, all operations must be performed with the cutterhead guard in place. After rabbeting, be sure to replace the guard.

9.PROPER CUTTING. When cutting, always keep the workpiece moving toward the outfeed table until the workpiece has passed completely over the cutterhead. Never back the work toward the infeed table.

10.USING GOOD STOCK. Jointing safety begins with your lumber. Inspect your stock carefully before you feed it over the cutterhead. Never joint a board that has loose knots, nails, or staples. If you have any doubts about the stability or structural integrity of your stock, DO NOT joint it!

Like all machines there is danger associated with this machine. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen the possibility of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.

No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious per- sonal injury, damage to equipment, or poor work results.

-10-

G0633/G0634 Jointer/Planer Combo Machine

Image 28
Contents Machine Inventory G0634Z only FigureTools Needed Qty Replacing Carbide Inserts G0634ZTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Planer Stand Assembly Stand Parts List DescriptionTable Assembly Cutterhead & Motor Cutterhead & Motor Parts List DescriptionDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard Fence/Guard Parts List PR01M EXT Retaining Ring 10MMSafety Labels and Cosmetic Parts H4978 T20446 H4979 AccessoriesH9893-Carbide Inserts 10 Pack JOINTER/PLANER Combination Machine Page Table of Contents Foreword Contact InfoG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controlsG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers 220V Operation Amperage DrawCircuit Requirements Plug/Receptacle Type GroundingSet Up Safety Items Needed for SetupUnpacking Description QtyCommon Components Qty Jointer/Planer Assembly Not shown InventoryG0633 only Figure G0634 only FigureHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadMoving & Placing Base Unit Front and right rear lifting hole LocationsSetting Outfeed Table Height To install the cutterhead guardCutterhead Guard To set the outfeed table heightDust Collection Knife Setting GaugeTo connect a dust collection hose Test Run To test run the machineRecommended Adjustments Tighten V-BeltsOperation Safety OperationsPage Basic Planer Controls To set up the machine for planer operationsJointer-Planer Conversion To change the machine for jointer opera- tions Planer dust port in down positionStock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointerSquaring Stock Thickness Planer Specific RulesSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerBasic Planer Operation Basic steps of operating the planer are as followsAccessories H1302 H4979 H4977Schedule CleaningBelts Lubrication Roller chainsPage Motor & Electrical TroubleshootingTable Jointer Cutting Jointer and Planer 43 orChecking/Adjusting Jointer Table Parallelism Checking Outfeed Table ParallelismChecking Infeed Table Parallelism Correcting Outfeed Table to Cutterhead ParallelismTo correct outfeed table parallelism To adjust the jointer table parallelism Adjusting Jointer Table ParallelismInfeed Table to Cutterhead Parallelism on Inspecting Knives G0633 Only To inspect the knives with the knife setting gaugeTo inspect the knives with a straightedge Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 Calibrating Depth Scale Pulley AlignmentTo calibrate the depth scale To align the pulleysSetting Fence Stops To set the 90˚ fence stopTo adjust the table lock levers Adjusting Table Lock LeversTo set the 45 fence stop Adjusting Gibs To adjust the table gibsTable Parallelism Adjustments To adjust the table parallelismPlaner Table Parallelism Table Parallelism InspectionTo adjust feed roller spring tension Spring TensionAnti-Kickback Fingers G0633/G0634 magnetic switch Electrical ComponentsWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MM801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page