Grizzly G0634Z manual JOINTER/PLANER Combination Machine

Page 17

MODEL G0633/G0634

JOINTER/PLANER

COMBINATION MACHINE

OWNER'S MANUAL

COPYRIGHT © APRIL, 2007 BY GRIZZLY INDUSTRIAL, INC., REVISED AUGUST, 2007 (BL)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BL8977 PRINTED IN TAIWAN

Image 17

Contents G0634Z only Figure Machine InventoryTo rotate or change a carbide insert Replacing Carbide Inserts G0634ZTools Needed Qty Machine Data Sheet Cutting Capacities Planer Stand Assembly Description Stand Parts ListTable Assembly Cutterhead & Motor Description Cutterhead & Motor Parts ListDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard PR01M EXT Retaining Ring 10MM Fence/Guard Parts ListSafety Labels and Cosmetic Parts H9893-Carbide Inserts 10 Pack AccessoriesH4978 T20446 H4979 JOINTER/PLANER Combination Machine Page Table of Contents Contact Info ForewordG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0634 identification and controls IdentificationG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Amperage Draw 220V OperationCircuit Requirements Plug/Receptacle Type GroundingItems Needed for Setup Set Up SafetyUnpacking Description QtyInventory Common Components Qty Jointer/Planer Assembly Not shownG0633 only Figure G0634 only FigureHardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadFront and right rear lifting hole Locations Moving & Placing Base UnitTo install the cutterhead guard Setting Outfeed Table HeightCutterhead Guard To set the outfeed table heightTo connect a dust collection hose Knife Setting GaugeDust Collection To test run the machine Test RunTighten V-Belts Recommended AdjustmentsOperations Operation SafetyPage Jointer-Planer Conversion To set up the machine for planer operationsBasic Planer Controls Planer dust port in down position To change the machine for jointer opera- tionsCorrect and incorrect grain alignment To cutterhead jointer Stock Inspection and RequirementsThickness Planer Specific Rules Squaring StockTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingBasic steps of operating the planer are as follows Basic Planer OperationAccessories H4979 H4977 H1302Belts CleaningSchedule Roller chains LubricationPage Table Jointer TroubleshootingMotor & Electrical 43 or Cutting Jointer and PlanerChecking Outfeed Table Parallelism Checking/Adjusting Jointer Table ParallelismTo correct outfeed table parallelism Correcting Outfeed Table to Cutterhead ParallelismChecking Infeed Table Parallelism Infeed Table to Cutterhead Parallelism on Adjusting Jointer Table ParallelismTo adjust the jointer table parallelism To inspect the knives with a straightedge To inspect the knives with the knife setting gaugeInspecting Knives G0633 Only Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 Pulley Alignment Calibrating Depth ScaleTo calibrate the depth scale To align the pulleysTo set the 90˚ fence stop Setting Fence StopsTo set the 45 fence stop Adjusting Table Lock LeversTo adjust the table lock levers To adjust the table gibs Adjusting GibsTo adjust the table parallelism Table Parallelism AdjustmentsPlaner Table Parallelism Table Parallelism InspectionSpring Tension To adjust feed roller spring tensionAnti-Kickback Fingers Electrical Components G0633/G0634 magnetic switchWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List PR01M EXT Retaining Ring 10MM Fence/Guard List801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page