Grizzly G0634Z manual Identification, G0634 identification and controls

Page 25

Identification

	X				F
	X				E
W					E		I
W							I	J
								J
				C		G	H
			B				H

		A
		A			D
					D
								K

R

S

T

V

U

Q

L

M

N

			O
			P

		Figure 1. G0634 identification and controls.
A.	Outfeed Table	N.	Infeed Table Lock Lever
B.	Fence	O.	Jointer Depth Scale
C.	Cutterhead Guard	P.	Magnetic Switch
D.	Fence Height Knobs	Q.	Emergency Off Button
E.	Quick Release Knobs	R.	Change Lever
F.	Tilt Lock	S.	Planer Table Lock
G.	Fence Lock Lever	T.	Planer Dust Port
H.	Fence Adjustment Knob	U.	Planer Table Height Handwheel
I.	Infeed Table Lock Knob	V.	Planer Table Height Scale
J.	Infeed Handgrip	W	Outfeed Table Adjustment Knob
K.	Infeed Table	X.	Outfeed Table Lock Knob

L.Jointer Dust Port

M.Planer Table

G0633/G0634 Jointer/Planer Combo Machine

-7-

Image 25

Contents G0634Z only Figure Machine InventoryTools Needed Qty Replacing Carbide Inserts G0634ZTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Planer Stand Assembly Description Stand Parts ListTable Assembly Cutterhead & Motor Description Cutterhead & Motor Parts ListDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard PR01M EXT Retaining Ring 10MM Fence/Guard Parts ListSafety Labels and Cosmetic Parts H4978 T20446 H4979 AccessoriesH9893-Carbide Inserts 10 Pack JOINTER/PLANER Combination Machine Page Table of Contents Contact Info ForewordG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0634 identification and controls IdentificationG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Amperage Draw 220V OperationCircuit Requirements Plug/Receptacle Type GroundingItems Needed for Setup Set Up SafetyUnpacking Description QtyInventory Common Components Qty Jointer/Planer Assembly Not shownG0633 only Figure G0634 only FigureHardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadFront and right rear lifting hole Locations Moving & Placing Base UnitTo install the cutterhead guard Setting Outfeed Table HeightCutterhead Guard To set the outfeed table heightDust Collection Knife Setting GaugeTo connect a dust collection hose To test run the machine Test RunTighten V-Belts Recommended AdjustmentsOperations Operation SafetyPage Basic Planer Controls To set up the machine for planer operationsJointer-Planer Conversion Planer dust port in down position To change the machine for jointer opera- tionsCorrect and incorrect grain alignment To cutterhead jointer Stock Inspection and RequirementsThickness Planer Specific Rules Squaring StockTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingBasic steps of operating the planer are as follows Basic Planer OperationAccessories H4979 H4977 H1302Schedule CleaningBelts Roller chains LubricationPage Motor & Electrical TroubleshootingTable Jointer 43 or Cutting Jointer and PlanerChecking Outfeed Table Parallelism Checking/Adjusting Jointer Table ParallelismChecking Infeed Table Parallelism Correcting Outfeed Table to Cutterhead ParallelismTo correct outfeed table parallelism To adjust the jointer table parallelism Adjusting Jointer Table ParallelismInfeed Table to Cutterhead Parallelism on Inspecting Knives G0633 Only To inspect the knives with the knife setting gaugeTo inspect the knives with a straightedge Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 Pulley Alignment Calibrating Depth ScaleTo calibrate the depth scale To align the pulleysTo set the 90˚ fence stop Setting Fence StopsTo adjust the table lock levers Adjusting Table Lock LeversTo set the 45 fence stop To adjust the table gibs Adjusting GibsTo adjust the table parallelism Table Parallelism AdjustmentsPlaner Table Parallelism Table Parallelism InspectionSpring Tension To adjust feed roller spring tensionAnti-Kickback Fingers Electrical Components G0633/G0634 magnetic switchWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List PR01M EXT Retaining Ring 10MM Fence/Guard List801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page