Grizzly G0634Z manual Set Up Safety, Items Needed for Setup, Unpacking, Description Qty

Page 31

SECTION 3: SET UP

Set Up Safety

This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine!

Wear safety glasses dur- ing the entire set up pro- cess!

The Model G0633/G0634 is a heavy machine. DO NOT over-exert yourself while unpacking or mov- ing your machine—get assistance.

G0633/G0634 Jointer/Planer Combo Machine

Items Needed for

Setup

The following items are needed to complete the setup process, but are not included with your machine:

Description		Qty
•	Safety Glasses (for each person)	.............. 1
•	Power Lifting Equipment	1

•Lifting Straps (800 lb. Capacity, Optional) . 1

•	Dust Collection System	1
• 4" Dust Hose (length as needed)		1
•	4" Hose Clamp	1
• Shop Rags for Cleaning		As needed
•	Solvent Cleaner	As needed

Unpacking

The Model G0633/G0634 was carefully packed when it left our warehouse. If you discover the machine is damaged after you have signed for delivery, please immediately call Customer Service at (570) 546-9663 for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi- tion of your shipment, inventory the contents.

-13-

Image 31

Contents G0634Z only Figure Machine InventoryTools Needed Qty Replacing Carbide Inserts G0634ZTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Planer Stand Assembly Description Stand Parts ListTable Assembly Cutterhead & Motor Description Cutterhead & Motor Parts ListDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard PR01M EXT Retaining Ring 10MM Fence/Guard Parts ListSafety Labels and Cosmetic Parts H4978 T20446 H4979 AccessoriesH9893-Carbide Inserts 10 Pack JOINTER/PLANER Combination Machine Page Table of Contents Contact Info ForewordG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0634 identification and controls IdentificationG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Plug/Receptacle Type Grounding 220V OperationAmperage Draw Circuit RequirementsDescription Qty Set Up SafetyItems Needed for Setup UnpackingG0634 only Figure Common Components Qty Jointer/Planer Assembly Not shownInventory G0633 only FigureHardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsFront and right rear lifting hole Locations Moving & Placing Base UnitTo set the outfeed table height Setting Outfeed Table HeightTo install the cutterhead guard Cutterhead GuardDust Collection Knife Setting GaugeTo connect a dust collection hose To test run the machine Test RunTighten V-Belts Recommended AdjustmentsOperations Operation SafetyPage Basic Planer Controls To set up the machine for planer operationsJointer-Planer Conversion Planer dust port in down position To change the machine for jointer opera- tionsCorrect and incorrect grain alignment To cutterhead jointer Stock Inspection and RequirementsThickness Planer Specific Rules Squaring StockTo surface plane on the jointer Surface PlaningTo edge joint on the jointer Edge JointingTo bevel cut on the jointer Bevel CuttingBasic steps of operating the planer are as follows Basic Planer OperationAccessories H4979 H4977 H1302Schedule CleaningBelts Roller chains LubricationPage Motor & Electrical TroubleshootingTable Jointer 43 or Cutting Jointer and PlanerChecking Outfeed Table Parallelism Checking/Adjusting Jointer Table ParallelismChecking Infeed Table Parallelism Correcting Outfeed Table to Cutterhead ParallelismTo correct outfeed table parallelism To adjust the jointer table parallelism Adjusting Jointer Table ParallelismInfeed Table to Cutterhead Parallelism on Inspecting Knives G0633 Only To inspect the knives with the knife setting gaugeTo inspect the knives with a straightedge Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To align the pulleys Calibrating Depth ScalePulley Alignment To calibrate the depth scaleTo set the 90˚ fence stop Setting Fence StopsTo adjust the table lock levers Adjusting Table Lock LeversTo set the 45 fence stop To adjust the table gibs Adjusting GibsTable Parallelism Inspection Table Parallelism AdjustmentsTo adjust the table parallelism Planer Table ParallelismSpring Tension To adjust feed roller spring tensionAnti-Kickback Fingers Electrical Components G0633/G0634 magnetic switchWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List PR01M EXT Retaining Ring 10MM Fence/Guard List801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page