Grizzly G0634Z manual Limit Switch Breakdown & List

Page 80

Limit Switch Breakdown & List

	��
	��
	��
	��	��
		��
��		��
��		��
		��
	��	��
	��
��
��		��
��
��		��
		��
	��	��
		��
��		��

REF	PART #	DESCRIPTION

501-1	P0633501-1	SWING LEVER (F)
501-2	P0633501-2	SWING LEVER (M)
501-3	P0633501-3	LIMIT SWITCH BRACKET
502	P0633502	COMPRESSION SPRING
503	P0633503	EXTENSION SPRING
504	P0633504	SWITCH ACTIVATION ROD
505	P0633505	SWITCH ACTIVATION ROD
506	P0633506	SWITCH ACTIVATION ROD
507	PLN03	LOCK NUT 5/16-18

REF	PART #	DESCRIPTION

508	PW07	FLAT WASHER 5/16
509	PB03	HEX BOLT 5/16-18 X 1
510	PB09	HEX BOLT 5/16-18 X 1/2
511	PN02	HEX NUT 5/16-18
512	PSB101	CAP SCREW 10-24 X 1-1/4
513	PSB06	CAP SCREW 1/4-20 X 1
514	P0633514	LIMIT SWITCH
515	P0633515	LIMIT SWITCH CONTROL CORD

-62-	G0633/G0634 Jointer/Planer Combo Machine

Image 80

Contents Machine Inventory G0634Z only FigureTo rotate or change a carbide insert Replacing Carbide Inserts G0634ZTools Needed Qty Machine Data Sheet Cutting Capacities Planer Stand Assembly Stand Parts List DescriptionTable Assembly Cutterhead & Motor Cutterhead & Motor Parts List DescriptionDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard Fence/Guard Parts List PR01M EXT Retaining Ring 10MMSafety Labels and Cosmetic Parts H9893-Carbide Inserts 10 Pack AccessoriesH4978 T20446 H4979 JOINTER/PLANER Combination Machine Page Table of Contents Foreword Contact InfoG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controlsG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers 220V Operation Amperage DrawCircuit Requirements Plug/Receptacle Type GroundingSet Up Safety Items Needed for SetupUnpacking Description QtyCommon Components Qty Jointer/Planer Assembly Not shown InventoryG0633 only Figure G0634 only FigureHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadMoving & Placing Base Unit Front and right rear lifting hole LocationsSetting Outfeed Table Height To install the cutterhead guardCutterhead Guard To set the outfeed table heightTo connect a dust collection hose Knife Setting GaugeDust Collection Test Run To test run the machineRecommended Adjustments Tighten V-BeltsOperation Safety OperationsPage Jointer-Planer Conversion To set up the machine for planer operationsBasic Planer Controls To change the machine for jointer opera- tions Planer dust port in down positionStock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointerSquaring Stock Thickness Planer Specific RulesSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerBasic Planer Operation Basic steps of operating the planer are as followsAccessories H1302 H4979 H4977Belts CleaningSchedule Lubrication Roller chainsPage Table Jointer TroubleshootingMotor & Electrical Cutting Jointer and Planer 43 orChecking/Adjusting Jointer Table Parallelism Checking Outfeed Table ParallelismTo correct outfeed table parallelism Correcting Outfeed Table to Cutterhead ParallelismChecking Infeed Table Parallelism Infeed Table to Cutterhead Parallelism on Adjusting Jointer Table ParallelismTo adjust the jointer table parallelism To inspect the knives with a straightedge To inspect the knives with the knife setting gaugeInspecting Knives G0633 Only Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 Calibrating Depth Scale Pulley AlignmentTo calibrate the depth scale To align the pulleysSetting Fence Stops To set the 90˚ fence stopTo set the 45 fence stop Adjusting Table Lock LeversTo adjust the table lock levers Adjusting Gibs To adjust the table gibsTable Parallelism Adjustments To adjust the table parallelismPlaner Table Parallelism Table Parallelism InspectionTo adjust feed roller spring tension Spring TensionAnti-Kickback Fingers G0633/G0634 magnetic switch Electrical ComponentsWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MM801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page