Grizzly G0634Z manual To adjust/replace the knives

Page 62

To adjust/replace the knives:

1.DISCONNECT THE JOINTER/PLANER FROM THE POWER SOURCE!

2.Remove the cutterhead guard from the table, and flip up the lower the infeed and outfeed tables. This will give you unrestricted access to the cutterhead.

3.Remove the motor access panel to expose the motor pulley.

4.Rotate the motor pulley to give you good access to one of the cutterhead knives.

Knives are sharp! When adjusting knives, wear gloves or cover knives with rags to avoid contact with knives, which could cause serious personal injury.

5.Loosen the cutterhead gib bolts, starting in the middle and alternating back and forth until all of the gib bolts are loose, but not falling out.

—If this is the first time you are setting the knives, remove the gib and knife from the cutterhead. Decide which adjustment option you are going to use between the jack screws and the springs.

—If you decide to use the jack screws, remove the springs from the cutterhead (they are located directly below the knives).

—If you decide to use the springs, just thread the jack screws completely into the cutterhead so they will not get lost. Replace the gib and knife.

6.Remove and clean the gibs and clean inside the cutterhead slot to remove all pitch or saw- dust. Coat the knives and gibs with a metal protectant (Page 32), then fit the gibs back in the cutterhead with the new knives.

7.Adjusting the knife heights:

-44-

Jack Screws: Using a 3mm hex wrench, find the jack screws through the access holes in the cutterhead (Figure 62) and rotate them to raise/lower the knife. When the knife is set correctly, it will barely touch the middle pad of the knife setting gauge. For now, only tighten the gib bolts enough to hold the knife in place. Repeat Steps 5–7with the other knives.

Figure 62. Jack screw access hole.

Springs: Push the knife down with the gauge so that the knife edge is touching the middle pad of the gauge. Hold the gauge down and only tighten the gib bolts enough to hold the knife in place. Repeat Steps 5–7with the other knives.

8.Rotate the cutterhead to the first knife you started with. Slightly tighten all the gib bolts by following the tightening sequence show in Figure 63. Repeat this step on the rest of the knives, then final tighten each gib bolt.

7

5

3

1

2

4

6

Figure 63. Gib tightening sequence.

9.If you used the knife setting gauge to set the knife heights, use the straightedge to adjust the outfeed table height evenly with the knives at top dead center (the highest point in their rotation). If you used the straightedge to set the knife heights, skip to the next step.

10.Replace the cutterhead guard and the motor access panel.

G0633/G0634 Jointer/Planer Combo Machine

Page 61 Page 63
Image 62
Page 61 Page 63
Contents Machine Inventory G0634Z only FigureTo rotate or change a carbide insert Replacing Carbide Inserts G0634ZTools Needed Qty Machine Data Sheet Cutting Capacities Planer Stand Assembly Stand Parts List DescriptionTable Assembly Cutterhead & Motor Cutterhead & Motor Parts List DescriptionDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard Fence/Guard Parts List PR01M EXT Retaining Ring 10MMSafety Labels and Cosmetic Parts H9893-Carbide Inserts 10 Pack AccessoriesH4978 T20446 H4979 JOINTER/PLANER Combination Machine Page Table of Contents Foreword Contact InfoG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controlsG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Circuit Requirements 220V OperationAmperage Draw Plug/Receptacle Type GroundingUnpacking Set Up SafetyItems Needed for Setup Description QtyG0633 only Figure Common Components Qty Jointer/Planer Assembly Not shownInventory G0634 only FigureHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadMoving & Placing Base Unit Front and right rear lifting hole LocationsCutterhead Guard Setting Outfeed Table HeightTo install the cutterhead guard To set the outfeed table heightTo connect a dust collection hose Knife Setting GaugeDust Collection Test Run To test run the machineRecommended Adjustments Tighten V-BeltsOperation Safety OperationsPage Jointer-Planer Conversion To set up the machine for planer operationsBasic Planer Controls To change the machine for jointer opera- tions Planer dust port in down positionStock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointerSquaring Stock Thickness Planer Specific RulesSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerBasic Planer Operation Basic steps of operating the planer are as followsAccessories H1302 H4979 H4977Belts CleaningSchedule Lubrication Roller chainsPage Table Jointer TroubleshootingMotor & Electrical Cutting Jointer and Planer 43 orChecking/Adjusting Jointer Table Parallelism Checking Outfeed Table ParallelismTo correct outfeed table parallelism Correcting Outfeed Table to Cutterhead ParallelismChecking Infeed Table Parallelism Infeed Table to Cutterhead Parallelism on Adjusting Jointer Table ParallelismTo adjust the jointer table parallelism To inspect the knives with a straightedge To inspect the knives with the knife setting gaugeInspecting Knives G0633 Only Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To calibrate the depth scale Calibrating Depth ScalePulley Alignment To align the pulleysSetting Fence Stops To set the 90˚ fence stopTo set the 45 fence stop Adjusting Table Lock LeversTo adjust the table lock levers Adjusting Gibs To adjust the table gibsPlaner Table Parallelism Table Parallelism AdjustmentsTo adjust the table parallelism Table Parallelism InspectionTo adjust feed roller spring tension Spring TensionAnti-Kickback Fingers G0633/G0634 magnetic switch Electrical ComponentsWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MM801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page
Top Page Image Contents