Grizzly G0634Z manual Test Run, To test run the machine

Page 38

Test Run

Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular operation. The test run consists of verifying the following: 1) The motor powers up and runs smoothly and without vibration and 2) the stop button safety feature works correctly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review Troubleshooting on Page 37.

If you cannot find a remedy, contact our Tech Support at (570) 546-9663 for assistance.

Before starting the jointer/planer, make sure you have performed the preceding assem- bly and adjustment instructions, and you have read through the rest of the manual and are familiar with the various functions and safety features on this machine. Failure to follow this warning could result in seri- ous personal injury or even death!

To test run the machine:

1.Make sure you understand the safety instruc- tions at the beginning of the manual and that the machine is setup properly.

2.Make sure all tools and objects used during setup are cleared away from the machine.

3.Make sure the jointer tables are folded down and locked in place (see Page 25).

4.Connect the machine to the power source.

5.Push the EMERGENCY OFF button in, then twist it clockwise so it pops out. See Figure 1, Page 7 for location of the EMERGENCY OFF button. When the OFF button pops out, the switch is reset and ready for operation (see Figure 17).

-20-

���

�

�

��������

������������

���������

����������

���

Figure 17. Resetting the Emergency Off switch.

6.Verify that the machine is operating correctly by pushing the green ON button.

—When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises.

—Investigate and correct strange or unusual noises or vibrations before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

7.Press the EMERGENCY OFF button to stop the machine.

8.WITHOUT resetting the switch, press the ON button. The machine should not start.

—If the machine does not start, the EMERGENCY OFF button safety feature is working correctly.

—If the machine does start (with the EMERGENCY OFF button pushed in), immediately disconnect power to the machine. The EMERGENCY OFF button safety feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

9.Press the ON button, then immediately press the OFF button on the magnetic box (Figure 1, Page 7).

—If the machine turns off, the OFF button is working correctly. The Test Run is com- plete.

—If the machine does not stop, disconnect power to the machine. The OFF button is not working correctly. This feature must work properly before proceeding with regu- lar operations. Call Tech Support for help.

G0633/G0634 Jointer/Planer Combo Machine

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Machine Inventory G0634Z only FigureTo rotate or change a carbide insert Replacing Carbide Inserts G0634ZTools Needed Qty Machine Data Sheet Cutting Capacities Planer Stand Assembly Stand Parts List DescriptionTable Assembly Cutterhead & Motor Cutterhead & Motor Parts List DescriptionDrive Assembly Breakdown Planer Table Limit Switch Fence/Guard Fence/Guard Parts List PR01M EXT Retaining Ring 10MMSafety Labels and Cosmetic Parts H9893-Carbide Inserts 10 Pack AccessoriesH4978 T20446 H4979 JOINTER/PLANER Combination Machine Page Table of Contents Foreword Contact InfoG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controlsG0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Circuit Requirements 220V OperationAmperage Draw Plug/Receptacle Type GroundingUnpacking Set Up SafetyItems Needed for Setup Description QtyG0633 only Figure Common Components Qty Jointer/Planer Assembly Not shownInventory G0634 only FigureHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadMoving & Placing Base Unit Front and right rear lifting hole LocationsCutterhead Guard Setting Outfeed Table HeightTo install the cutterhead guard To set the outfeed table heightTo connect a dust collection hose Knife Setting GaugeDust Collection Test Run To test run the machineRecommended Adjustments Tighten V-BeltsOperation Safety OperationsPage Jointer-Planer Conversion To set up the machine for planer operationsBasic Planer Controls To change the machine for jointer opera- tions Planer dust port in down positionStock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointerSquaring Stock Thickness Planer Specific RulesSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerBasic Planer Operation Basic steps of operating the planer are as followsAccessories H1302 H4979 H4977Belts CleaningSchedule Lubrication Roller chainsPage Table Jointer TroubleshootingMotor & Electrical Cutting Jointer and Planer 43 orChecking/Adjusting Jointer Table Parallelism Checking Outfeed Table ParallelismTo correct outfeed table parallelism Correcting Outfeed Table to Cutterhead ParallelismChecking Infeed Table Parallelism Infeed Table to Cutterhead Parallelism on Adjusting Jointer Table ParallelismTo adjust the jointer table parallelism To inspect the knives with a straightedge To inspect the knives with the knife setting gaugeInspecting Knives G0633 Only Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To calibrate the depth scale Calibrating Depth ScalePulley Alignment To align the pulleysSetting Fence Stops To set the 90˚ fence stopTo set the 45 fence stop Adjusting Table Lock LeversTo adjust the table lock levers Adjusting Gibs To adjust the table gibsPlaner Table Parallelism Table Parallelism AdjustmentsTo adjust the table parallelism Table Parallelism InspectionTo adjust feed roller spring tension Spring TensionAnti-Kickback Fingers G0633/G0634 magnetic switch Electrical ComponentsWiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MM801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page
Top Page Image Contents