Metabo HC 410 Three-phase motors 220/380/400/415 volts, Legislation and Codes of Practice

Page 15

U.K Supplement to Operating Instructions for metabo HC 410 Combination Surfacing and Thicknessing Machine

Please note the following supplementary information associated with this machine:

U.K. Legislation and Codes of Practice

When used industrially within the U.K. this machine falls under the scope of

-Whoodworking Machines Regulations 1974 and

-Used and Provisions of Work Equipment Regulations 1992

We strongly advice you study and follow these regulations.

Paragraph 7.3 Connection to Power Mains

230 V motor. The motor supplied with this machine will not run on a 13 A domestic ring main. On starting the machine a high current of very short duration is drawn, which will blow your 13A fuse. This machine can only be connected to a 16A separate radial circuit using BS 4343 (CEE 17) socket and plug. Ensure the installation is protected by a suitably sized fuse or miniature circuit breaker.

This work should only be undertaken by a qualified electrician!

Wiring Instructions

Warning: This appliance must be earthed!

If the plug, fitted to the power cable supplied with the machine, has to be changed or replaced, connect the mains lead conductors in accordance with the following colour code.

Three-phase motors (220/380/400/415 volts):

Machines with a 3-phase motor are connected to power mains using a 5-pin industrial appliance-inlet/connector according to VDE 0623/BS 4343/IEC 309.

4-wire mains lead

Yellow/green

-

Earth

 

Brown

-

Phase (L1)

 

Black

-

Phase (L2)

 

Black

-

Phase (L3)

5-wire mains lead

Yellow/green

-

Earth

 

Brown

-

Phase (L1)

 

Black

-

Phase (L2)

 

Black

-

Phase (L3)

 

Blue

-

Neutral

IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN!

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Betriebsanleitung Abricht- und Dickenhobelmaschine Page Lieferumfang InhaltsverzeichnisTechnische Daten Produkthaftung/GarantieInbetriebnahme Erstmontage SonderzubehšrEinsatzbereich/Verwendungszweck TransporthinweiseSpŠneabsaugung AufstellungNetzanschlu§ Drehrichtung11 ZufŸhrhilfen Abrichten WerkstŸckabmessungenWerkstŸck-Voruntersuchung 10 GefŠhrliche ArbeitsgŠngeVerstellung des FŸgeanschlages Bedienelemente Terminal/Elektrische AusrŸstungUnterspannungsrelais/Motorschutzschalter MotorbremseJustieren Einstellen der Spanabnahme/SkalenablesungJustierung des Anschlaglineales Einstellen der Messerwellen-Schutzeinrichtung12.8 UmrŸsten der Maschine zum Dickenhobel Einstellung des DickentischesJustieren der Dickentischskala Vorschubabschaltung Arbeitshinweise DickenhobelnAbrichten von flachen WerkstŸcken Abrichten von Schmalseiten 14 TŠgliche SicherheitsprŸfungAus-/Einbau, Einstellung der Hobelmesser Ausbau der Hobelmesser 15.2 PrŸfung der eingebauten HobelmesserAllgemeine Pflege- und Wartungsarbeiten Schmierung Nachspannen/Auswechseln der Antriebsriemen Auswechseln der RŸckschlaggreifer16.4 PrŸfung der Sicherheitsendschalter/Motorbremse Demontage der Hobelmesserwelle Auswechseln der VorschubwalzenThree-phase motors 220/380/400/415 volts Paragraph 7.3 Connection to Power MainsLegislation and Codes of Practice Standard Delivery ContentsSpecifications User ResponsibilityTransportation Optional AccessoriesInstallation/Initial Operation Final Assembly Scope of ApplicationDirection of Rotation InstallationConnection to Power Mains SafetyPlaning/Jointing Workpiece DimensionsStock Pre-Checking Push Blocks and Feeding FixturesMotor Brake Controls Switch Terminal/Electrical EquipmentSwitch/Overload Protection Canting Fence AdjustmentSetting of Fence Cutter Guard SettingSetting Depth of Cut/Scale Reading Changing to Thicknessing Mode Thicknesser Bed SettingThicknesser Scale Adjustment Feed Gear Clutch Operation TicknessingPlaning/Surfacing Flat Stock Daily Safety Checks Replacing/Setting the Planer BladesJointing Edges Checking Planer Blade Setting Care and Maintenance LubricationPlaner Blade Removal Drive Belt Tension/Replacement Checking Limit Switches and MotorbrakeServicing/Replacing the Recoil Lock Changing the Cutterblock Changing the Feed RollersFournitures ˆ la livraison Table des matiresCaractŽristiques techniques ResponsabilitŽ/GarantieConsignes de transport Accessoires en optionMise en service Premier montage Domaine dutilisation / UtilisationDŽmarrage automatique du dispositif daspiration des sciures Raccordement au secteurSens de rotation Aspiration des sciuresAides dattaque 11.1 DŽgauchissage Dimensions de la pice ˆ usinerInspection prŽalable de la pice ˆ usiner 10 OpŽrations de travail dangereusesRelais ˆ minimum de tension/contacteur-disjoncteur Freinage de larbre12.4 RŽglage de la butŽe RŽglage Ajustement de la rgle de guidageMontage du dispositif de protection de larbre porte-fers 12.7 RŽglage de la profondeur de passe/lecture de lŽchelleTransformation de la machine en raboteuse 12.9 RŽglage de la table de rabotageAjustage de lŽchelle de la table de rabotage 12.11 DŽsactivation de lentranement Instructions de travail Rabotage13.2 DŽgauchissage de pices planes 13.3 DŽgauchissage de faces Žtroites Contrles de sŽcuritŽ quotidiensMontage et dŽmontage, rŽglage des rabots Maintenance gŽnŽrale et entretien Graissage 15.1 DŽmontage des fersContrle des fers montŽs Resserrage/Remplacement des courroies dentranement Remplacement des griffes de sŽcuritŽ anti-rejetsContrle des interrupteurs fin de course/Freinage de larbre 16.6 DŽmontage de larbre porte-fers Remplacement des rouleaux dentranementLeveringsomvang InhoudTechnische gegevens Produktverantwoordelijkheid/GarantieIngebruikname Eerste montage Speciaal toebehorenGebruiksmogelijkheden GebruiknameStofafzuiging OpstellingAansluiting op het net DraairichtingHulpstukken bij de aanvoer Vlakken Afmetingen van de werkstukken HC 410 DKontrole der werkstukken Gevaarlijke bewerkingenInstellen van de langsgeleider Bedieningselementen Terminal/elektrische uitrustingMotorbeveiliging MotorremPrecies instellen Afstelling van de aanslaglineaalAfstellen van de beschermkap over de schaafas Instelling van de spaanafname/Aflezing op de skalaPrecies afstellen van de skala van de vandikte tafel Instellen van de vandikte tafelUitschakeling van de voeding Tips bij het gebruik Vandikte schavenVlakken van vlakke werkstukken Vlakken van smalle latten Dagelijkse veiligheids-kontroleMonteren en uitbouwen en instellen van de schaafmessen Kontrole van de ingebouwde schaafmessen Demonteren van de schaafmessenAlgemene onderhoudswerken Smering Naspannen/Uitwisselen van de aandrijfriemenUitwisselen van de terugslagkleppen Kontrole van de veiligheids eindschakelaars/Motorrem Uitwisselen van de voedingswalsenDemontage van de schaafmesas Achtung

HC 410 specifications

The Metabo HC 410 is a powerful and versatile tool designed for precision cutting, making it a favorite among professionals and DIY enthusiasts alike. As a part of Metabo's renowned lineup of high-quality tools, the HC 410 combines advanced technology and ergonomic design, ensuring optimal performance in various applications.

One of the standout features of the Metabo HC 410 is its robust motor, which delivers exceptional power for cutting through a variety of materials. With a rated input power of 1,300 watts and a maximum output power of 1,800 watts, this machine is capable of handling demanding tasks without compromising on efficiency. The motor is engineered for durability, promising longevity even under heavy use.

The HC 410 is equipped with a high-quality saw blade that ensures clean and accurate cuts. The saw blade can be easily adjusted to accommodate different cutting angles and depths, making it incredibly versatile. This flexibility allows users to achieve precise cuts for various projects, whether they are working with wood, plastic, or other materials.

An important aspect of the HC 410 is its innovative dust extraction system. This feature minimizes the amount of dust created during cutting, leading to a cleaner workspace and improved visibility. The dust extraction port can be connected to a vacuum system, ensuring that users can maintain a tidy work area without interrupting their workflow.

Another key characteristic of the Metabo HC 410 is its user-friendly design. The tool includes an ergonomic handle that provides a comfortable grip, reducing fatigue during extended use. Additionally, the safety features, including a blade guard and an electric brake, ensure that the tool can be operated safely, even by less experienced users.

The HC 410 is also designed with portability in mind. Its lightweight construction and compact design make it easy to transport and store, making it a practical choice for both job sites and home workshops. With its blend of power, precision, and user-centric features, the Metabo HC 410 is a reliable tool that meets the needs of a diverse range of applications, making it a valuable addition to any tool collection. Whether you are cutting materials for renovation projects or crafting custom pieces, the HC 410 delivers outstanding performance and quality.
Top Page Image Contents