Metabo HC 410 Controls Switch Terminal/Electrical Equipment, Switch/Overload Protection

Page 20

12 Controls

12.1Switch Terminal/Electrical Equipment

The raised switch panel can be turned to point towards the operator position for easy access. Turn rotary switch clockwise to start machine, turn coun- ter-clockwise to switch the machine off. To prevent unauthorized use the switch can be blocked with a padlock.

Three limit switches, located behind the thicknesser drive gear cover, pre- vent the starting of the machine if it is not properly set for the planing or thicknessing mode. The limit switches will also switch the machine off if

-the planing beds are swung up

-the chip ejection hood is swung from the cutterblock when thick- nessing

12.2Switch/Overload Protection

The switch is equipped with a no-volt release solenoid (magnetic switch), to prevent start-up after a power failure. If the machine is not connected to the power mains the switch does not engage. In the event of a power failure the machine has to be restarted. In case of an overload of the motor the build-in motor protection relay trips and cuts the power to the motor. If the motor is shut off repeatedly by the overload relay, check machine (motor brake action, blade sharpness, low voltage etc.) A cooling down period of 10 min. is recommended before switching ON again.

12.3Motor Brake

The motor supplied with this machine is equipped with an electro-mechanical motor brake, designed for a long service life. Friction, however, causes the brake pad to wear. If the braking action fades (time to cutterblock standstill exceeds 10 sec.) the motorbrake has to be replaced. The max. permissible number of 10 switching actuation per hour should not be exceeded.

12.4Canting Fence Adjustment

A

B

Loosening the ratchet lever (A) al- lows for lateral adjustment of the fence carrier.

After loosening both ratchet levers (B) the fence can be set from the 90° position to the 45° position.

When changing from planing to thick- nessing mode the fence is swung up.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Betriebsanleitung Abricht- und Dickenhobelmaschine Page Inhaltsverzeichnis Technische DatenProdukthaftung/Garantie LieferumfangSonderzubehšr Einsatzbereich/VerwendungszweckTransporthinweise Inbetriebnahme ErstmontageAufstellung Netzanschlu§Drehrichtung SpŠneabsaugungWerkstŸckabmessungen WerkstŸck-Voruntersuchung10 GefŠhrliche ArbeitsgŠnge 11 ZufŸhrhilfen AbrichtenBedienelemente Terminal/Elektrische AusrŸstung Unterspannungsrelais/MotorschutzschalterMotorbremse Verstellung des FŸgeanschlagesEinstellen der Spanabnahme/Skalenablesung Justierung des AnschlaglinealesEinstellen der Messerwellen-Schutzeinrichtung JustierenJustieren der Dickentischskala 12.8 UmrŸsten der Maschine zum DickenhobelEinstellung des Dickentisches Abrichten von flachen WerkstŸcken VorschubabschaltungArbeitshinweise Dickenhobeln Aus-/Einbau, Einstellung der Hobelmesser Abrichten von Schmalseiten14 TŠgliche SicherheitsprŸfung Allgemeine Pflege- und Wartungsarbeiten Schmierung Ausbau der Hobelmesser15.2 PrŸfung der eingebauten Hobelmesser 16.4 PrŸfung der Sicherheitsendschalter/Motorbremse Nachspannen/Auswechseln der AntriebsriemenAuswechseln der RŸckschlaggreifer Auswechseln der Vorschubwalzen Demontage der HobelmesserwelleLegislation and Codes of Practice Three-phase motors 220/380/400/415 voltsParagraph 7.3 Connection to Power Mains Contents SpecificationsUser Responsibility Standard DeliveryOptional Accessories Installation/Initial Operation Final AssemblyScope of Application TransportationInstallation Connection to Power MainsSafety Direction of RotationWorkpiece Dimensions Stock Pre-CheckingPush Blocks and Feeding Fixtures Planing/JointingControls Switch Terminal/Electrical Equipment Switch/Overload ProtectionCanting Fence Adjustment Motor BrakeSetting Depth of Cut/Scale Reading Setting of FenceCutter Guard Setting Thicknesser Scale Adjustment Changing to Thicknessing ModeThicknesser Bed Setting Planing/Surfacing Flat Stock Feed Gear ClutchOperation Ticknessing Jointing Edges Daily Safety ChecksReplacing/Setting the Planer Blades Planer Blade Removal Checking Planer Blade SettingCare and Maintenance Lubrication Servicing/Replacing the Recoil Lock Drive Belt Tension/ReplacementChecking Limit Switches and Motorbrake Changing the Feed Rollers Changing the CutterblockTable des matires CaractŽristiques techniquesResponsabilitŽ/Garantie Fournitures ˆ la livraisonAccessoires en option Mise en service Premier montageDomaine dutilisation / Utilisation Consignes de transportRaccordement au secteur Sens de rotationAspiration des sciures DŽmarrage automatique du dispositif daspiration des sciuresDimensions de la pice ˆ usiner Inspection prŽalable de la pice ˆ usiner10 OpŽrations de travail dangereuses Aides dattaque 11.1 DŽgauchissage12.4 RŽglage de la butŽe Relais ˆ minimum de tension/contacteur-disjoncteurFreinage de larbre Ajustement de la rgle de guidage Montage du dispositif de protection de larbre porte-fers12.7 RŽglage de la profondeur de passe/lecture de lŽchelle RŽglageAjustage de lŽchelle de la table de rabotage Transformation de la machine en raboteuse12.9 RŽglage de la table de rabotage 13.2 DŽgauchissage de pices planes 12.11 DŽsactivation de lentranementInstructions de travail Rabotage Montage et dŽmontage, rŽglage des rabots 13.3 DŽgauchissage de faces ŽtroitesContrles de sŽcuritŽ quotidiens Contrle des fers montŽs Maintenance gŽnŽrale et entretien Graissage15.1 DŽmontage des fers Contrle des interrupteurs fin de course/Freinage de larbre Resserrage/Remplacement des courroies dentranementRemplacement des griffes de sŽcuritŽ anti-rejets Remplacement des rouleaux dentranement 16.6 DŽmontage de larbre porte-fersInhoud Technische gegevensProduktverantwoordelijkheid/Garantie LeveringsomvangSpeciaal toebehoren GebruiksmogelijkhedenGebruikname Ingebruikname Eerste montageOpstelling Aansluiting op het netDraairichting StofafzuigingAfmetingen van de werkstukken HC 410 D Kontrole der werkstukkenGevaarlijke bewerkingen Hulpstukken bij de aanvoer VlakkenBedieningselementen Terminal/elektrische uitrusting MotorbeveiligingMotorrem Instellen van de langsgeleiderAfstelling van de aanslaglineaal Afstellen van de beschermkap over de schaafasInstelling van de spaanafname/Aflezing op de skala Precies instellenInstellen van de vandikte tafel Precies afstellen van de skala van de vandikte tafelVlakken van vlakke werkstukken Uitschakeling van de voedingTips bij het gebruik Vandikte schaven Monteren en uitbouwen en instellen van de schaafmessen Vlakken van smalle lattenDagelijkse veiligheids-kontrole Demonteren van de schaafmessen Kontrole van de ingebouwde schaafmessenUitwisselen van de terugslagkleppen Algemene onderhoudswerken SmeringNaspannen/Uitwisselen van de aandrijfriemen Demontage van de schaafmesas Kontrole van de veiligheids eindschakelaars/MotorremUitwisselen van de voedingswalsen Achtung

HC 410 specifications

The Metabo HC 410 is a powerful and versatile tool designed for precision cutting, making it a favorite among professionals and DIY enthusiasts alike. As a part of Metabo's renowned lineup of high-quality tools, the HC 410 combines advanced technology and ergonomic design, ensuring optimal performance in various applications.

One of the standout features of the Metabo HC 410 is its robust motor, which delivers exceptional power for cutting through a variety of materials. With a rated input power of 1,300 watts and a maximum output power of 1,800 watts, this machine is capable of handling demanding tasks without compromising on efficiency. The motor is engineered for durability, promising longevity even under heavy use.

The HC 410 is equipped with a high-quality saw blade that ensures clean and accurate cuts. The saw blade can be easily adjusted to accommodate different cutting angles and depths, making it incredibly versatile. This flexibility allows users to achieve precise cuts for various projects, whether they are working with wood, plastic, or other materials.

An important aspect of the HC 410 is its innovative dust extraction system. This feature minimizes the amount of dust created during cutting, leading to a cleaner workspace and improved visibility. The dust extraction port can be connected to a vacuum system, ensuring that users can maintain a tidy work area without interrupting their workflow.

Another key characteristic of the Metabo HC 410 is its user-friendly design. The tool includes an ergonomic handle that provides a comfortable grip, reducing fatigue during extended use. Additionally, the safety features, including a blade guard and an electric brake, ensure that the tool can be operated safely, even by less experienced users.

The HC 410 is also designed with portability in mind. Its lightweight construction and compact design make it easy to transport and store, making it a practical choice for both job sites and home workshops. With its blend of power, precision, and user-centric features, the Metabo HC 410 is a reliable tool that meets the needs of a diverse range of applications, making it a valuable addition to any tool collection. Whether you are cutting materials for renovation projects or crafting custom pieces, the HC 410 delivers outstanding performance and quality.
Top Page Image Contents