Miller Electric IH, TS manual Select File Select New Chart, Select Add Point

Page 42

New instrument is displayed.

Select “OK” to add the Instrument tag.

scrn11

Select “File”.

Select “New Chart”.

scrn12

Select “Add Point”.

scrn13

OM-203 185 Page 38

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Description OM-203 185FProcesses File Induction HeatingFrom Miller to You Table of Contents Resetting All RAM Variables In The Event Of Display Errors Induction Heating Hazards − Safety Precautions − Read Before UsingSymbol Usage Electric Shock can killPrincipal Safety Standards California Proposition 65 WarningsEMF Information About Pacemakers− Mesures DE Securite Pour LE Chauffage PAR Induction LE Chauffage PAR Induction peut être dangereuxLE Chauffage PAR Induction peut provoquer un incendie DES Organes Mobiles peuvent provoquer des blessures Porteurs de stimulateur cardiaque, restez à distanceEn ce qui concerne les stimulateurs cardiaques − Introduction IH/TS Installation − InstallationSpecifications Specification DescriptionConnecting To Power Source Input 14 Pin Information For Receptacle RC1Connecting 25kW System Cords And Cables FrontRear Cooler Connecting 5kW System Cords And CablesFrontRear Such as grinders, drills, lights, etcConnecting External Device − Components and Controls IH/TS Front PanelIH/TS Rear Panel 200.0 ControllerIH/TS Setup Select Power Source − Setup and OperationSafety Equipment Parameter DisplayLocale Setup Time Date Setup − Digital2-2 Login As Engineer 2-1 Digital Recorder ControlsGo To Home Screen Time And Date SetupLogin As User Channel Cycling On/Off And NotesRun List Sub-Menu Definitions OperationController Display Definitions NameController Operation Segment Type Definitions Programming The 2408 ControllerProgram List Terms And Definitions Setpoint remains constant for a specified periodExample Pre−heat Profile Ramp rate Example Stress Relief ProfileStep to 600 F Deg/ hrRamp to 800 F Ramp to 600 F Example Multi−Step Stress Relief ProfileRamp to 800 F @ 400 /hr Ramp to 1250 F Deg/hrProfile Set-Up Worksheet Sets output toBatch Recording Using 5100 Digital Recorder Begin Batch recording -3-3-1. Login As UserStart Recording Stop Recording Saving Data To a Disk Recommended After Each BatchNetwork Connection Windows 95, 98, ME Changing IP Address To Connect The IH/TS For WindowsDownloading Files From Recorder Troubleshooting Connection Problems For Windows 95, 98, MERunning a Program To Preheat Or Stress Relief Recovering From An Interruption OP1 SP2Viewing Data In Review Software Installing Review Software And First Time SetupReview software first time setup screen Backing Up The DatabaseRunning Review Software Start Review softwareSelect Transfer Files Select Files Single File With Batch Name Select OKSingle File With No Batch Name Select Start TransferMultiple Files With Batch Names Multiple Files With No Batch NamesSelect File Select New Chart Select Add PointScrn14 Select OK to view chart These steps must be done Scrn20 Select OK Comment becomes part of the chart Select Save File name becomes Part of the chart Select File Select Print to print entire profile on oneScrn30 Typical Profile Chart Printout − Configuring Controller and Recorder For each Channel Number Select Channel NumberDate Setup Load FileTime Setup Login As UserGo To Home Screen Troubleshooting − Maintenance & TroubleshootingRoutine Maintenance MonthsGoto ConF, IA ConF Module 1 Config. See Section If display flashes no.io again, or ifBefore 10 degree window is See Section When touched, but does notIs complete, turn Ihts power off and back on again Advance to next screenDiagnostic Procedures For IH/TS OM-203 185 5100V Recorder Displays Channel Error Resetting All RAM Variables In The Event Of Display Errors Press Page to Press Scroll Factory Set ParametersController Version Number Version NumberController Edit Parameters Varies Controller Full Parameters Prior To VersionNavigation Across Scroll Down Home List Output ListConfigure Parameters Prior To Version ControllerNavigation Across Controller Full Parameters Effective w/Version OM-203 Navigation Across Scroll Down Home ListConfigure Parameters Effective w/Version Fluke-714 Thermocouple Calibration Certification ProcedureType-K Mini Connector Calibrator− Electrical Diagrams Circuit Diagram For IH/TS− Parts List Complete Assembly198 Page Page Service Your distributor also givesSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s
Top Page Image Contents