Miller Electric TS, IH Calibration Certification Procedure, Fluke-714 Thermocouple, Calibrator

Page 69

8-6. Calibration Certification Procedure

The following items are required for verifying calibration:

1.Fluke-714 Thermocouple Calibrator

this can be obtained from: http://www.fluke.com/products/home.asp?SID=13&AGID=9&PID=1707 specify primary standard certification when ordering.

2.Type-K Mini Connector (Fluke #80CK-M) Or Equivalent

this can be obtained from: http://thermo-electric-direct.com.control.interliant.com/ Miniature_Quick-Coupling_Thermocouple_Connectors10630.html

3.Type-K 2-Pin Male Connector

this can be obtained from: http://thermo-electric-direct.com.control.interliant.com/ Standard_Quick-Coupling_Thermocouple_Connectors7886.html

4.Calibration Labels − Part No. QCC306BU BLUE

these can be obtained from: http://www.q-cees.com/itemdetail.asp?part=206

5.A length of type-K thermocouple wire connected between the type-K mini connector and type-K 2-pin connector.

2		1.	Fluke-714 Thermocouple
			Calibrator
1		2.	Type-K Mini Connector
		2.	Type-K Mini Connector
	3	3.	Type-K 2-Pin Male Connector
	3	4.	Calibration Labels
		4.	Calibration Labels
		4

Perform the procedure as follows:

1.Press the down arrow on bottom left of digital recorder to display numeric page.

. Allow readings to stabilize before recording.

2.Set Fluke-714 TC Calibrator to 382.0 degrees F.

a.Move TC Calibrator from TC1 through TC6 in sequence recording each value read onto the Certificate of Calibration.

b.Verify readings are within ±3 degrees F of TC Calibrator.

.If readings are beyond the +3degrees F, the instrument will need to be returned to Eurotherm for repair.

Phone: 703-669-1316

E-mail: repairs@eurotherm.com

web page: www.eurotherm3.com/repairs.htm

c.Repeat at 882.0 degrees F and at 1382.0 degrees F

3.Save a copy of the Certificate using the IH/TS serial no. and date as the file name, i.e. “LB056241 062501” for June 25, 2001.

4.Print a copy of the certificate to send with the IH/TS.

5.Complete calibration sticker and apply to IH/TS front panel below recorder.

I.D. No. (IH/TS serial no.)

By (your initials) Date (today’s date) Due (date 1 year from today)

OM-203 185 Page 65

Image 69

Contents Processes OM-203 185FDescription File Induction HeatingFrom Miller to You Table of Contents Resetting All RAM Variables In The Event Of Display Errors Symbol Usage − Safety Precautions − Read Before UsingInduction Heating Hazards Electric Shock can killCalifornia Proposition 65 Warnings Principal Safety StandardsAbout Pacemakers EMF Information− Mesures DE Securite Pour LE Chauffage PAR Induction LE Chauffage PAR Induction peut être dangereuxLE Chauffage PAR Induction peut provoquer un incendie Porteurs de stimulateur cardiaque, restez à distance DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques − Introduction Specifications − InstallationIH/TS Installation Specification DescriptionInput 14 Pin Information For Receptacle RC1 Connecting To Power SourceConnecting 25kW System Cords And Cables FrontRear FrontRear Connecting 5kW System Cords And CablesCooler Such as grinders, drills, lights, etcConnecting External Device IH/TS Front Panel − Components and ControlsIH/TS Rear Panel Controller 200.0Safety Equipment − Setup and OperationIH/TS Setup Select Power Source Parameter Display2-2 Login As Engineer Time Date Setup − DigitalLocale Setup 2-1 Digital Recorder ControlsLogin As User Time And Date SetupGo To Home Screen Channel Cycling On/Off And NotesController Display Definitions OperationRun List Sub-Menu Definitions NameController Operation Program List Terms And Definitions Programming The 2408 ControllerSegment Type Definitions Setpoint remains constant for a specified periodExample Pre−heat Profile Step to 600 F Example Stress Relief ProfileRamp rate Deg/ hrRamp to 800 F @ 400 /hr Ramp to 1250 F Example Multi−Step Stress Relief ProfileRamp to 800 F Ramp to 600 F Deg/hrSets output to Profile Set-Up WorksheetBatch Recording Using 5100 Digital Recorder Begin Batch recording -3-3-1. Login As UserStart Recording Saving Data To a Disk Recommended After Each Batch Stop RecordingNetwork Connection Windows 95, 98, ME Changing IP Address To Connect The IH/TS For WindowsDownloading Files From Recorder For Windows 95, 98, ME Troubleshooting Connection ProblemsRunning a Program To Preheat Or Stress Relief OP1 SP2 Recovering From An InterruptionReview software first time setup screen Installing Review Software And First Time SetupViewing Data In Review Software Backing Up The DatabaseRunning Review Software Start Review softwareSelect Transfer Files Select Files Select OK Single File With Batch NameSelect Start Transfer Single File With No Batch NameMultiple Files With No Batch Names Multiple Files With Batch NamesSelect Add Point Select File Select New ChartScrn14 Select OK to view chart These steps must be done Scrn20 Select OK Comment becomes part of the chart Select Save Select File Select Print to print entire profile on one File name becomes Part of the chartScrn30 Typical Profile Chart Printout − Configuring Controller and Recorder Select Channel Number For each Channel NumberLoad File Date SetupTime Setup Login As UserGo To Home Screen Routine Maintenance − Maintenance & TroubleshootingTroubleshooting MonthsGoto ConF, IA ConF Module 1 Config. See Section If display flashes no.io again, or ifBefore 10 degree window is Is complete, turn Ihts power off and back on again When touched, but does notSee Section Advance to next screenDiagnostic Procedures For IH/TS OM-203 185 5100V Recorder Displays Channel Error Resetting All RAM Variables In The Event Of Display Errors Controller Version Number Factory Set ParametersPress Page to Press Scroll Version NumberController Edit Parameters Navigation Across Scroll Down Home List Controller Full Parameters Prior To VersionVaries Output ListConfigure Parameters Prior To Version ControllerNavigation Across OM-203 Navigation Across Scroll Down Home List Controller Full Parameters Effective w/VersionConfigure Parameters Effective w/Version Type-K Mini Connector Calibration Certification ProcedureFluke-714 Thermocouple CalibratorCircuit Diagram For IH/TS − Electrical DiagramsComplete Assembly − Parts List198 Page Page Service Your distributor also givesSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s