Miller Electric TS, IH Connecting To Power Source, Input 14 Pin Information For Receptacle RC1

Page 13

4-3. Connecting To Power Source

5

I J K AB

H N L C

G M D

F E

1

6

3

2

Turn Off power source.

1. IH/TS

2. Interconnecting Cord

3. 14-Socket Plug

4. 14-Pin Plug

Obtain cord with 14-socket plug on one end and 14-pin plug on other end.

5. Keyway

6. Remote 14 Receptacle RC1 (See Section 4-4)

To connect cord to a receptacle, align keyway, insert plug, and tighten threaded collar.

To connect remaining end of cord to power source, align keyway, insert plug, and tighten threaded collar.

4

sb7.1* 3/93 - Ref. S-0004-A / S-0750 / Ref. 802 926 / Ref. 801 049 / 801 825-B / Ref. 803 004-A

4-4. Input 14 Pin Information For Receptacle RC1

	REMOTE 14	Pin	Pin Information


	Remote Contactor	A	+24 volts dc from power source.
	Remote Contactor	B	Contact closure to A completes power source +24 volts dc contactor control circuit.
		B

	Remote Output Control	D	Control circuit common.
	Remote Output Control	E	0 to +10 volts dc signal for power source output control.
		E	0 to +10 volts dc signal for power source output control.

	Power Source Fault	F, J	Absence of contact closure from power source indicates power source output failure.

		I	Actual frequency input signal.
	Remote Metering*	L	Average power input signal.
	Remote Metering*	M	Voltage input signal RMS.
		M	Voltage input signal RMS.
		N	Current input signal RMS.

*See power source Owner’s Manual for scaling information.

OM-203 185 Page 9

Image 13

Contents

Processes OM-203 185FDescription File Induction HeatingFrom Miller to You Table of Contents Resetting All RAM Variables In The Event Of Display Errors Symbol Usage − Safety Precautions − Read Before UsingInduction Heating Hazards Electric Shock can killCalifornia Proposition 65 Warnings Principal Safety StandardsAbout Pacemakers EMF InformationLE Chauffage PAR Induction peut être dangereux − Mesures DE Securite Pour LE Chauffage PAR InductionLE Chauffage PAR Induction peut provoquer un incendie Porteurs de stimulateur cardiaque, restez à distance DES Organes Mobiles peuvent provoquer des blessures En ce qui concerne les stimulateurs cardiaques − Introduction Specifications − InstallationIH/TS Installation Specification DescriptionInput 14 Pin Information For Receptacle RC1 Connecting To Power SourceFront Connecting 25kW System Cords And CablesRear FrontRear Connecting 5kW System Cords And CablesCooler Such as grinders, drills, lights, etcConnecting External Device IH/TS Front Panel − Components and ControlsIH/TS Rear Panel Controller 200.0Safety Equipment − Setup and OperationIH/TS Setup Select Power Source Parameter Display2-2 Login As Engineer Time Date Setup − DigitalLocale Setup 2-1 Digital Recorder ControlsLogin As User Time And Date SetupGo To Home Screen Channel Cycling On/Off And NotesController Display Definitions OperationRun List Sub-Menu Definitions NameController Operation Program List Terms And Definitions Programming The 2408 ControllerSegment Type Definitions Setpoint remains constant for a specified periodExample Pre−heat Profile Step to 600 F Example Stress Relief ProfileRamp rate Deg/ hrRamp to 800 F @ 400 /hr Ramp to 1250 F Example Multi−Step Stress Relief ProfileRamp to 800 F Ramp to 600 F Deg/hrSets output to Profile Set-Up WorksheetBegin Batch recording -3-3-1. Login As User Batch Recording Using 5100 Digital RecorderStart Recording Saving Data To a Disk Recommended After Each Batch Stop RecordingChanging IP Address To Connect The IH/TS For Windows Network Connection Windows 95, 98, MEDownloading Files From Recorder For Windows 95, 98, ME Troubleshooting Connection ProblemsRunning a Program To Preheat Or Stress Relief OP1 SP2 Recovering From An InterruptionReview software first time setup screen Installing Review Software And First Time SetupViewing Data In Review Software Backing Up The DatabaseStart Review software Running Review SoftwareSelect Transfer Files Select Files Select OK Single File With Batch NameSelect Start Transfer Single File With No Batch NameMultiple Files With No Batch Names Multiple Files With Batch NamesSelect Add Point Select File Select New ChartScrn14 Select OK to view chart These steps must be done Scrn20 Select OK Comment becomes part of the chart Select Save Select File Select Print to print entire profile on one File name becomes Part of the chartScrn30 Typical Profile Chart Printout − Configuring Controller and Recorder Select Channel Number For each Channel NumberLoad File Date SetupLogin As User Time SetupGo To Home Screen Routine Maintenance − Maintenance & TroubleshootingTroubleshooting MonthsIf display flashes no.io again, or if Goto ConF, IA ConF Module 1 Config. See SectionBefore 10 degree window is Is complete, turn Ihts power off and back on again When touched, but does notSee Section Advance to next screenDiagnostic Procedures For IH/TS OM-203 185 5100V Recorder Displays Channel Error Resetting All RAM Variables In The Event Of Display Errors Controller Version Number Factory Set ParametersPress Page to Press Scroll Version NumberController Edit Parameters Navigation Across Scroll Down Home List Controller Full Parameters Prior To VersionVaries Output ListController Configure Parameters Prior To VersionNavigation Across OM-203 Navigation Across Scroll Down Home List Controller Full Parameters Effective w/VersionConfigure Parameters Effective w/Version Type-K Mini Connector Calibration Certification ProcedureFluke-714 Thermocouple CalibratorCircuit Diagram For IH/TS − Electrical DiagramsComplete Assembly − Parts List198 Page Page Your distributor also gives ServiceSupport Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s