Miller Electric TS, IH manual For each Channel Number, Select Channel Number

Page 53

7-2. Changing 5100V Recorder From Degrees F to Degrees C And Change TC Descriptor

Log in as “Engineer” (see Section 6-2-2-2).

Press “Menu” (bottom right of display).

Select “Config“.

Select “Channels” from pull down menu.

scrn32

For each Channel Number (1-6):

1. Select “Channel Number”.

2. Maximum expected temperature range reading: 1500 for °F typ.

(1472 °F) = 800 for °C typ.

3. Range units can be changed between 5F and 5C.

4. Descriptor can be changed in “Descriptor” field, if desired.

Press “Apply”. Log out.

scrn33

OM-203 185 Page 49

Image 53

Contents Processes OM-203 185FDescription File Induction HeatingFrom Miller to You Table of Contents Resetting All RAM Variables In The Event Of Display Errors Symbol Usage − Safety Precautions − Read Before UsingInduction Heating Hazards Electric Shock can killCalifornia Proposition 65 Warnings Principal Safety StandardsAbout Pacemakers EMF InformationLE Chauffage PAR Induction peut provoquer un incendie − Mesures DE Securite Pour LE Chauffage PAR InductionLE Chauffage PAR Induction peut être dangereux Porteurs de stimulateur cardiaque, restez à distance DES Organes Mobiles peuvent provoquer des blessuresEn ce qui concerne les stimulateurs cardiaques − Introduction Specifications − InstallationIH/TS Installation Specification DescriptionInput 14 Pin Information For Receptacle RC1 Connecting To Power SourceRear Connecting 25kW System Cords And CablesFront FrontRear Connecting 5kW System Cords And CablesCooler Such as grinders, drills, lights, etcConnecting External Device IH/TS Front Panel − Components and ControlsIH/TS Rear Panel Controller 200.0Safety Equipment − Setup and OperationIH/TS Setup Select Power Source Parameter Display2-2 Login As Engineer Time Date Setup − DigitalLocale Setup 2-1 Digital Recorder ControlsLogin As User Time And Date SetupGo To Home Screen Channel Cycling On/Off And NotesController Display Definitions OperationRun List Sub-Menu Definitions NameController Operation Program List Terms And Definitions Programming The 2408 ControllerSegment Type Definitions Setpoint remains constant for a specified periodExample Pre−heat Profile Step to 600 F Example Stress Relief ProfileRamp rate Deg/ hrRamp to 800 F @ 400 /hr Ramp to 1250 F Example Multi−Step Stress Relief ProfileRamp to 800 F Ramp to 600 F Deg/hrSets output to Profile Set-Up WorksheetStart Recording Batch Recording Using 5100 Digital RecorderBegin Batch recording -3-3-1. Login As User Saving Data To a Disk Recommended After Each Batch Stop RecordingDownloading Files From Recorder Network Connection Windows 95, 98, MEChanging IP Address To Connect The IH/TS For Windows For Windows 95, 98, ME Troubleshooting Connection ProblemsRunning a Program To Preheat Or Stress Relief OP1 SP2 Recovering From An InterruptionReview software first time setup screen Installing Review Software And First Time SetupViewing Data In Review Software Backing Up The DatabaseSelect Transfer Files Running Review SoftwareStart Review software Select Files Select OK Single File With Batch NameSelect Start Transfer Single File With No Batch NameMultiple Files With No Batch Names Multiple Files With Batch NamesSelect Add Point Select File Select New ChartScrn14 Select OK to view chart These steps must be done Scrn20 Select OK Comment becomes part of the chart Select Save Select File Select Print to print entire profile on one File name becomes Part of the chartScrn30 Typical Profile Chart Printout − Configuring Controller and Recorder Select Channel Number For each Channel NumberLoad File Date SetupGo To Home Screen Time SetupLogin As User Routine Maintenance − Maintenance & TroubleshootingTroubleshooting MonthsBefore 10 degree window is Goto ConF, IA ConF Module 1 Config. See SectionIf display flashes no.io again, or if Is complete, turn Ihts power off and back on again When touched, but does notSee Section Advance to next screenDiagnostic Procedures For IH/TS OM-203 185 5100V Recorder Displays Channel Error Resetting All RAM Variables In The Event Of Display Errors Controller Version Number Factory Set ParametersPress Page to Press Scroll Version NumberController Edit Parameters Navigation Across Scroll Down Home List Controller Full Parameters Prior To VersionVaries Output ListNavigation Across Configure Parameters Prior To VersionController OM-203 Navigation Across Scroll Down Home List Controller Full Parameters Effective w/VersionConfigure Parameters Effective w/Version Type-K Mini Connector Calibration Certification ProcedureFluke-714 Thermocouple CalibratorCircuit Diagram For IH/TS − Electrical DiagramsComplete Assembly − Parts List198 Page Page Support ServiceYour distributor also gives Miller Electric Mfg. Co To locate a Distributor or Service Agency visitFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s