Miller Electric DS-64M Swingarc manual Front Panel Controls, Side And Rear Panel Controls

Page 22

5-3. Front Panel Controls

1

8

2

3

7

4

4

 

6

ST-162 127

5

5

 

1Display

2Parameter Select Button

Press button to move > (the cursor) on the display.

3 Display Control

Turn control to change value pointed to by >.

Turning control one click causes Trim (arc length) to increase/decrease by one or Volts to increase/decrease by 0.1.

When IPM is selected, turning control one click causes wire feed speed (IPM) to in- crease/decrease by one.

When MPM is selected, turning control three clicks causes wire feed speed (MPM) to in- crease by 0.1.

When Prg # is selected, turning control one click causes program number (Prg #) to in- crease/decrease by one.

The program number cannot be changed while welding, with exception of Dual Sched-

ule Mode (see Section 7).

SharpArc™ is “Arc” on the display (see Sec- tion12). It is used to adjust arc cone width and arc characteristics.

Pulse is a default setting. To change type of process (Pulse, Adaptive Pulse, or MIG) use side panel controls (see Section 5-4).

4Active Side Indicator Light

5Trigger Hold Button And Indicator Light

Trigger Hold can be set on a per program ba- sis. Indicator light comes on for programs where this feature is active.

To weld without holding gun trigger through- out weld cycle, press and release button to turn feature on (indicator light turns on).

To start weld cycle, press and release gun trigger within three seconds after an arc has been struck. To end weld cycle, press and re- lease gun trigger.

6 Side Select Button

The feeder remembers the last used program for each side and returns to that program when the active side is changed.

.The gun trigger may be used to change active side of the feeder.

7 Jog Button

Push to momentarily feed welding wire with- out energizing welding circuit or shielding gas valve.

Jog speed is varied using the Display Control while Jog button is pressed. Default setting is 200 IPM.

8 Purge Button

Push to momentarily energize gas valve with- out energizing the welding circuit.

.Jog and Purge only work on the active side of the feeder.

Holding the Jog and Purge buttons at the same time displays pulse parameters on the side panel display and voltage on front panel display.

5-4. Side And Rear Panel Controls

13

8 7

5

6

Rear Panel

2

 

4

1Mode Display

2Mode Select Button

Press button to move > in display.

3Parameter Display

4Parameter Select Button

Press button to move > in display.

5Parameter Increase Button

6Parameter Decrease Button

7Power Switch

8Circuit Breaker CB1

CB1 protects the wire feeder from overload.

Ref. ST-162 128 / Ref. ST-162 133

OM-1588 Page 18

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Description OM-1588161 875SProcesses File MIG GmawFrom Miller to You Table of Contents Teach Using 15 Points Redefining Teach Points − Teach PointsArc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier DES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer unIncendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures graves’EMPLOI Excessif peut SUR Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaquesInstalling Swivel Into Pipe Post − InstallationSpecifications − IntroductionInstalling Control Box And Adjusting Tilt Installing Boom And Reel SupportInstalling Wire Guide Extension Equipment Connection Diagram 300/400 Ampere Model CC/CV Inverter Welding Power SourceConnecting Weld Cables And Gas Hoses Pin Plug Information Control Box ConnectionsPin Pin Information Motor Speed Wire Type Wire Size Feed Speed Capability Removing Safety Collar And Adjusting BoomWire Type, Size, And Feed Speed Capability Table Gun Recommendation TableInstalling And Threading Welding Wire Operational Terms − OperationPulse Welding Terms Front Panel Controls Side And Rear Panel Controls− Setting Sequence Parameters Sequence Parameters In a Program− Setting Dual Schedule Parameters Selecting Dual Schedule PairOptional Dual Schedule Switch Diagrams Data Card Terms − Using the Optional Data CardInstalling Data Card Amperage Apk Peak Abk BackgroundCard Displays Entering Access Code Definable Values Standard SecurityMotor − System Setup Accessing The Setup MenuCard is in card slot, program will be loaded from card System Setup Display ParametersRemote ShutdownProgram 2 − Steel Wire Size/Type Gas Ar CO2 or Ar Oxy / 40 CFH 19 L/mProgram 1 − Steel Program 3 − SteelProgram 6 − Stainless Steel Program 4 − SteelProgram 5 − Stainless Steel Program 7 − Metal Core305 29.6 400 37.2 127 137340 33.3 285 27.7Program 7 − Nickel Alloy Program 4 − Stainless SteelGas Ar He / 40 CFH 19 L/m Selecting And Adjusting SharpArcE Control Parameter Select ArcTeach Using 15 Points − Teach PointsRedefining Pulse Parameters Redefining Teach PointsRedefining IPM Teach Point Do this for each teach pointMfg. Date Date Program Number Wire Size/TypeEquipment Used − Power Source Serial Number Wire Feeder CFHL/minDisconnect power before maintaining − Maintenance and TroubleshootingRoutine Maintenance Motor Start ControlError Displays Release Trigger Error DisplayTrouble Remedy TroubleshootingDisconnect power before troubleshooting PullOM-1588 − Electrical Diagram Circuit DiagramSD-184 792-B − Parts List 16-4 16-2 26 27 16-5Optional Support, Hub & Reel -1 Item Panel, Front w/Components -4 Item Control Box 16-3Control Box -1 Item Drive Assembly, Wire Drive Assembly, Wire -1 Items 29 Roll Drive Roll and Wire Guide KitsFraction Metric Kit RollPanel, Side w/Components -4 Item Boom Assembly Boom Assembly -1 Item OM-1588 Your distributor also gives ServiceSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s
Top Page Image Contents