Miller Electric DS-64M Swingarc System Setup Display Parameters, Remote, Shutdown, Is sensed

Page 31

9-2. System Setup Display Parameters

Note

See Menu Guide for detailed programming steps.

 

 

DISPLAY SETTING

NOTES

 

 

>System

Select the process the welding power source is able to do.

 

 

>Model

For the Invision 456 and XMT 304 selections, pulse data and welding power source minimum and maximum voltage

 

values are automatically loaded in. For the “Other” selection, welding power source minimum and maximum voltage

 

and amperage values must be entered. Pulse data defaults to Invision 456 values.

 

 

>Access♦

When on, restricts use of setup screens.

 

 

>Mig Type

Default is Off. Set to On only for older CV welding power source without voltage feedback at 14-socket receptacle.

 

 

>Voltage

Default is 14-pin receptacle. Use V. Sense when more than 50 ft (15m) of weld cable is used (including gun cable

 

length).

 

 

>Arc Start*

Use Hot Start only with Inverter Model welding power source and large diameter wires. The arc starts in CV and

 

switches to CC.

 

 

>Dual Schedule

See Section 7-2.

 

 

>Trigger

When on, trigger can be used to switch between programs that have at least 0.2 seconds of preflow time programmed.

 

 

>Remote

When on, an optional dual schedule switch with a “y” trigger cable adapter cord can be used to change Volts or Trim,

 

IPM, SharpArc, or Prg depending on where the front panel display > is.

 

 

>Arc Time

Displays accumulated arc time and cycles.

 

 

>Wire Feed

Choose to display inches per minute or meters per minute and motor type, but installed motor must match selection.

 

 

>Memory

No Reset: allows operator to exit memory reset parameter without resetting any data.

 

Program Reset: unit defaults to original factory setting for the last active program. Setup information does not change.

 

If setup card is in card slot, program will be loaded from card.

 

System Reset: unit defaults to original factory settings for all programs and setup excluding System and Arc Time. If

 

setup card is in card slot, program will be loaded from card.

 

Total Reset: unit defaults to original factory settings for all programs and setup including System and Arc Time. If setup

 

card is in card slot, program will be loaded from card.

 

 

>Shutdown

When on, the system immediately shuts down if no arc voltage is sensed. When off, wire feeds even if no arc voltage

 

is sensed.

 

 

>Gas Flow♦♦

Setting must be Meter Off if option is not installed.

 

 

>Ramps

Turns start and crater ramping On or Off. When On, output power is tapered from start to weld and from weld to crater.

 

 

>Software

Know this when talking with service personnel.

 

 

♦Can be used only when optional data card is inserted.

* Selection does not appear on display when MIG Only is System choice.

♦♦Must remain set to Meter Off if option is not installed to prevent system error.

OM-1588 Page 27

Page 30 Page 32
Image 31
Page 30 Page 32
Contents File MIG Gmaw OM-1588161 875SProcesses DescriptionFrom Miller to You Table of Contents − Teach Points Teach Using 15 Points Redefining Teach PointsElectric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier DES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer unIncendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut SUREn ce qui concerne les stimulateurs cardiaques Principales normes de sécurité− Introduction − InstallationSpecifications Installing Swivel Into Pipe PostInstalling Boom And Reel Support Installing Control Box And Adjusting TiltInstalling Wire Guide Extension 300/400 Ampere Model CC/CV Inverter Welding Power Source Equipment Connection DiagramConnecting Weld Cables And Gas Hoses Pin Plug Information Control Box ConnectionsPin Pin Information Gun Recommendation Table Removing Safety Collar And Adjusting BoomWire Type, Size, And Feed Speed Capability Table Motor Speed Wire Type Wire Size Feed Speed CapabilityInstalling And Threading Welding Wire Operational Terms − OperationPulse Welding Terms Side And Rear Panel Controls Front Panel ControlsSequence Parameters In a Program − Setting Sequence ParametersSelecting Dual Schedule Pair − Setting Dual Schedule ParametersOptional Dual Schedule Switch Diagrams Amperage Apk Peak Abk Background − Using the Optional Data CardInstalling Data Card Data Card TermsCard Displays Entering Access Code Definable Values Standard SecurityMotor Accessing The Setup Menu − System SetupShutdown System Setup Display ParametersRemote Card is in card slot, program will be loaded from cardProgram 3 − Steel Wire Size/Type Gas Ar CO2 or Ar Oxy / 40 CFH 19 L/mProgram 1 − Steel Program 2 − SteelProgram 7 − Metal Core Program 4 − SteelProgram 5 − Stainless Steel Program 6 − Stainless Steel285 27.7 400 37.2 127 137340 33.3 305 29.6Program 7 − Nickel Alloy Program 4 − Stainless SteelGas Ar He / 40 CFH 19 L/m Parameter Select Arc Selecting And Adjusting SharpArcE Control− Teach Points Teach Using 15 PointsDo this for each teach point Redefining Teach PointsRedefining IPM Teach Point Redefining Pulse ParametersCFHL/min Date Program Number Wire Size/TypeEquipment Used − Power Source Serial Number Wire Feeder Mfg. DateMotor Start Control − Maintenance and TroubleshootingRoutine Maintenance Disconnect power before maintainingRelease Trigger Error Display Error DisplaysPull TroubleshootingDisconnect power before troubleshooting Trouble RemedyOM-1588 Circuit Diagram − Electrical DiagramSD-184 792-B 16-4 16-2 26 27 16-5 − Parts ListOptional Support, Hub & Reel -1 Item Panel, Front w/Components -4 Item 16-3 Control BoxControl Box -1 Item Drive Assembly, Wire Drive Assembly, Wire -1 Items 29 Kit Roll Drive Roll and Wire Guide KitsFraction Metric RollPanel, Side w/Components -4 Item Boom Assembly Boom Assembly -1 Item OM-1588 Your distributor also gives ServiceSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact
Top Page Image Contents