Miller Electric DS-64M Swingarc manual Control Box, 16-3

Page 50

. Hardware is common and not available unless listed.

15	17
	16

		13	14	18
		13	14	19
			20	21	22	24
10	11			21	22	23
9		12				2
	PC80
8		7				25
		6				27
	4	5
						26
	PC1
		3
		2

1

		28
		16-3
PC40	29	Fig

Fig 16-7	37	36	PC10		PC50	30	29
			35
			34	33	32	31

ST-800 273-B

Figure 16-4. Control Box

OM-1588 Page 46

Image 50

Contents Description OM-1588161 875SProcesses File MIG GmawFrom Miller to You Table of Contents Teach Using 15 Points Redefining Teach Points − Teach PointsArc Welding Hazards Symbol UsageMarks a special safety message Electric Shock can killFlying Metal can injure eyes ARC Rays can burn eyes and skinWelding can cause fire or explosion Buildup of GAS can injure or killCalifornia Proposition 65 Warnings About Pacemakers Principal Safety StandardsEMF Information Indique un message de sécurité particulier UNE Décharge Électrique peut entraîner la mortLES Fumées ET LES GAZ peuvent être dangereux DES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer unIncendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures graves’EMPLOI Excessif peut SUR Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaquesInstalling Swivel Into Pipe Post − InstallationSpecifications − IntroductionInstalling Control Box And Adjusting Tilt Installing Boom And Reel SupportInstalling Wire Guide Extension Equipment Connection Diagram 300/400 Ampere Model CC/CV Inverter Welding Power SourceConnecting Weld Cables And Gas Hoses Pin Pin Information Control Box ConnectionsPin Plug Information Motor Speed Wire Type Wire Size Feed Speed Capability Removing Safety Collar And Adjusting BoomWire Type, Size, And Feed Speed Capability Table Gun Recommendation TableInstalling And Threading Welding Wire Pulse Welding Terms − OperationOperational Terms Front Panel Controls Side And Rear Panel Controls− Setting Sequence Parameters Sequence Parameters In a Program− Setting Dual Schedule Parameters Selecting Dual Schedule PairOptional Dual Schedule Switch Diagrams Data Card Terms − Using the Optional Data CardInstalling Data Card Amperage Apk Peak Abk BackgroundCard Displays Entering Access Code Motor SecurityDefinable Values Standard − System Setup Accessing The Setup MenuCard is in card slot, program will be loaded from card System Setup Display ParametersRemote ShutdownProgram 2 − Steel Wire Size/Type Gas Ar CO2 or Ar Oxy / 40 CFH 19 L/mProgram 1 − Steel Program 3 − SteelProgram 6 − Stainless Steel Program 4 − SteelProgram 5 − Stainless Steel Program 7 − Metal Core305 29.6 400 37.2 127 137340 33.3 285 27.7Gas Ar He / 40 CFH 19 L/m Program 4 − Stainless SteelProgram 7 − Nickel Alloy Selecting And Adjusting SharpArcE Control Parameter Select ArcTeach Using 15 Points − Teach PointsRedefining Pulse Parameters Redefining Teach PointsRedefining IPM Teach Point Do this for each teach pointMfg. Date Date Program Number Wire Size/TypeEquipment Used − Power Source Serial Number Wire Feeder CFHL/minDisconnect power before maintaining − Maintenance and TroubleshootingRoutine Maintenance Motor Start ControlError Displays Release Trigger Error DisplayTrouble Remedy TroubleshootingDisconnect power before troubleshooting PullOM-1588 − Electrical Diagram Circuit DiagramSD-184 792-B − Parts List 16-4 16-2 26 27 16-5Optional Support, Hub & Reel -1 Item Panel, Front w/Components -4 Item Control Box 16-3Control Box -1 Item Drive Assembly, Wire Drive Assembly, Wire -1 Items 29 Roll Drive Roll and Wire Guide KitsFraction Metric Kit RollPanel, Side w/Components -4 Item Boom Assembly Boom Assembly -1 Item OM-1588 Support ServiceYour distributor also gives For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s