Miller Electric DS-64M Swingarc manual Drive Assembly, Wire

Page 52

.Hardware is common and not available unless listed.

	See Table 16-1 For
	Drive Roll & Wire Guide Kits			18
				19
				20
				21
				22
			17	23
				24
				16
				25
	7			15
	7
	6
5	8			14
	9			14
	9
	4		10	12
				12
				11
	3			11
	2			26
	2
1				13
	2
				27
	39		40	28
			40
			41
			42
	38
	37
	36
				29
	35		30	1
	34			1
	34
	33	32	31

ST-801 456−A

Figure 16-5. Drive Assembly, Wire

OM-1588 Page 48

Image 52

Contents OM-1588161 875S ProcessesDescription File MIG GmawFrom Miller to You Table of Contents Teach Using 15 Points Redefining Teach Points − Teach PointsSymbol Usage Marks a special safety messageArc Welding Hazards Electric Shock can killARC Rays can burn eyes and skin Welding can cause fire or explosionFlying Metal can injure eyes Buildup of GAS can injure or killCalifornia Proposition 65 Warnings EMF Information Principal Safety StandardsAbout Pacemakers LES Fumées ET LES GAZ peuvent être dangereux UNE Décharge Électrique peut entraîner la mortIndique un message de sécurité particulier LE Soudage peut provoquer un Incendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent provoquer des brûlures gravesRisque D’INCENDIE OU D’EXPLO LA Chute DE L’APPAREIL peut blesser’EMPLOI Excessif peut SUR DES Organes Mobiles peuvent provoquer des blessuresPrincipales normes de sécurité En ce qui concerne les stimulateurs cardiaques− Installation SpecificationsInstalling Swivel Into Pipe Post − IntroductionInstalling Control Box And Adjusting Tilt Installing Boom And Reel SupportInstalling Wire Guide Extension Equipment Connection Diagram 300/400 Ampere Model CC/CV Inverter Welding Power SourceConnecting Weld Cables And Gas Hoses Pin Plug Information Control Box ConnectionsPin Pin Information Removing Safety Collar And Adjusting Boom Wire Type, Size, And Feed Speed Capability TableMotor Speed Wire Type Wire Size Feed Speed Capability Gun Recommendation TableInstalling And Threading Welding Wire Operational Terms − OperationPulse Welding Terms Front Panel Controls Side And Rear Panel Controls− Setting Sequence Parameters Sequence Parameters In a Program− Setting Dual Schedule Parameters Selecting Dual Schedule PairOptional Dual Schedule Switch Diagrams − Using the Optional Data Card Installing Data CardData Card Terms Amperage Apk Peak Abk BackgroundCard Displays Entering Access Code Definable Values Standard SecurityMotor − System Setup Accessing The Setup MenuSystem Setup Display Parameters RemoteCard is in card slot, program will be loaded from card ShutdownWire Size/Type Gas Ar CO2 or Ar Oxy / 40 CFH 19 L/m Program 1 − SteelProgram 2 − Steel Program 3 − SteelProgram 4 − Steel Program 5 − Stainless SteelProgram 6 − Stainless Steel Program 7 − Metal Core400 37.2 127 137 340 33.3305 29.6 285 27.7Program 7 − Nickel Alloy Program 4 − Stainless SteelGas Ar He / 40 CFH 19 L/m Selecting And Adjusting SharpArcE Control Parameter Select ArcTeach Using 15 Points − Teach PointsRedefining Teach Points Redefining IPM Teach PointRedefining Pulse Parameters Do this for each teach pointDate Program Number Wire Size/Type Equipment Used − Power Source Serial Number Wire FeederMfg. Date CFHL/min− Maintenance and Troubleshooting Routine MaintenanceDisconnect power before maintaining Motor Start ControlError Displays Release Trigger Error DisplayTroubleshooting Disconnect power before troubleshootingTrouble Remedy PullOM-1588 − Electrical Diagram Circuit DiagramSD-184 792-B − Parts List 16-4 16-2 26 27 16-5Optional Support, Hub & Reel -1 Item Panel, Front w/Components -4 Item Control Box 16-3Control Box -1 Item Drive Assembly, Wire Drive Assembly, Wire -1 Items 29 Drive Roll and Wire Guide Kits Fraction MetricRoll Kit RollPanel, Side w/Components -4 Item Boom Assembly Boom Assembly -1 Item OM-1588 Your distributor also gives ServiceSupport To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s