Miller Electric DS-64M Swingarc manual Installing Wire Guide Extension

Page 15

4-4. Installing Wire Guide Extension

1

4

3

2

1Wire Guide Fitting

2Bolt

3Monocoil Liner

4Wire Guide Extension

Tighten bolt to secure liner in wire guide fitting. Do not overtighten bolt and crush liner.

Repeat procedure for opposite side.

Tools Needed:

3/8 in

ST-152 383

OM-1588 Page 11

Image 15

Contents File MIG Gmaw OM-1588161 875SProcesses DescriptionFrom Miller to You Table of Contents − Teach Points Teach Using 15 Points Redefining Teach PointsElectric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesCalifornia Proposition 65 Warnings Principal Safety Standards EMF InformationAbout Pacemakers UNE Décharge Électrique peut entraîner la mort LES Fumées ET LES GAZ peuvent être dangereuxIndique un message de sécurité particulier DES Pièces Chaudes peuvent provoquer des brûlures graves LE Soudage peut provoquer unIncendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OU D’EXPLOLA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peut SUREn ce qui concerne les stimulateurs cardiaques Principales normes de sécurité− Introduction − InstallationSpecifications Installing Swivel Into Pipe PostInstalling Boom And Reel Support Installing Control Box And Adjusting TiltInstalling Wire Guide Extension 300/400 Ampere Model CC/CV Inverter Welding Power Source Equipment Connection DiagramConnecting Weld Cables And Gas Hoses Control Box Connections Pin Plug InformationPin Pin Information Gun Recommendation Table Removing Safety Collar And Adjusting BoomWire Type, Size, And Feed Speed Capability Table Motor Speed Wire Type Wire Size Feed Speed CapabilityInstalling And Threading Welding Wire − Operation Operational TermsPulse Welding Terms Side And Rear Panel Controls Front Panel ControlsSequence Parameters In a Program − Setting Sequence ParametersSelecting Dual Schedule Pair − Setting Dual Schedule ParametersOptional Dual Schedule Switch Diagrams Amperage Apk Peak Abk Background − Using the Optional Data CardInstalling Data Card Data Card TermsCard Displays Entering Access Code Security Definable Values StandardMotor Accessing The Setup Menu − System SetupShutdown System Setup Display ParametersRemote Card is in card slot, program will be loaded from cardProgram 3 − Steel Wire Size/Type Gas Ar CO2 or Ar Oxy / 40 CFH 19 L/mProgram 1 − Steel Program 2 − SteelProgram 7 − Metal Core Program 4 − SteelProgram 5 − Stainless Steel Program 6 − Stainless Steel285 27.7 400 37.2 127 137340 33.3 305 29.6Program 4 − Stainless Steel Program 7 − Nickel AlloyGas Ar He / 40 CFH 19 L/m Parameter Select Arc Selecting And Adjusting SharpArcE Control− Teach Points Teach Using 15 PointsDo this for each teach point Redefining Teach PointsRedefining IPM Teach Point Redefining Pulse ParametersCFHL/min Date Program Number Wire Size/TypeEquipment Used − Power Source Serial Number Wire Feeder Mfg. DateMotor Start Control − Maintenance and TroubleshootingRoutine Maintenance Disconnect power before maintainingRelease Trigger Error Display Error DisplaysPull TroubleshootingDisconnect power before troubleshooting Trouble RemedyOM-1588 Circuit Diagram − Electrical DiagramSD-184 792-B 16-4 16-2 26 27 16-5 − Parts ListOptional Support, Hub & Reel -1 Item Panel, Front w/Components -4 Item 16-3 Control BoxControl Box -1 Item Drive Assembly, Wire Drive Assembly, Wire -1 Items 29 Kit Roll Drive Roll and Wire Guide KitsFraction Metric RollPanel, Side w/Components -4 Item Boom Assembly Boom Assembly -1 Item OM-1588 Service Your distributor also givesSupport Your distributor and/or equipment manufacturer’s To locate a Distributor or Service Agency visitMiller Electric Mfg. Co For assistance in filing or settling claims, contact