DeWalt D28114R instruction manual 2and 5 Sanding Flap Discs, Operation, Guards and Flanges

Page 11

4-1/2"and 5" Sanding Flap Discs

NOTE: The

guard is pre-adjusted to the

diameter of

the gear case hub at the

Type 27 guard

hubbed sanding

flap disc

Type 27 guard

Quick-Change

backing flange

non-hubbed sanding

flap disc

threaded clamp nut

factory. If, after a period of time, the guard

P

becomes loose, tighten the adjusting screw

 

(P) with clamp lever in the closed position.

CAUTION: Do not tighten the adjusting

screw with the clamp lever in open position. Undetectable damage to the guard or the mounting hub may result.

CAUTION: If guard cannot be tightened by adjusting clamp, do not use tool and take the tool and guard to a service center to repair or replace the guard.

OPERATION

WARNING: Always observe the safety instructions and applicable regulations.

WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories.

Guards and Flanges

It is important to choose the correct guards and flanges to use

English

3.With the guard latch open, rotate the guard (I) into the desired working position. The guard body should be positioned between the spindle and the operator to provide maximum operator protection.

4.Close the guard latch to secure the guard

on the gear case. You should not be able

 

to rotate the guard by hand when the

 

latch is closed. Do not operate the grinder

 

with a loose guard or the clamp lever in

I

open position.

 

5.To remove the guard, open the guard latch, rotate the guard so that the arrows are aligned and pull up on the guard.

with the grinder accessories. See pages 7–9 for the correct accessories.

NOTE: Edge grinding and cutting can be performed with Type 27 wheels designed and specified for this purpose.

WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated accessory speed may burst and cause injury. Every unthreaded accessory must have a 7/8" arbor hole. If it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 7–9. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Esmerilhador de Ângulo Pequeno 115 mm/125 mm 4-1/2/5 Page Electrical Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Work Area SafetyService Specific Safety RulesAdditional Specific Safety Instructions for Grinders Power Tool USE and CareCauses and Operator Prevention of Kickback Always Wear EYE Protection When Using this ToolVoltage Volts Total length of cord in meters m Intended USE Description FIGRotating the Gear Case FeaturesAssembly and Adjustments AccessoriesMounting and Removing Guard 2 and 5 Grinding WheelsMounting Guard Sanding Discs Wire WheelsGuards and Flanges 2and 5 Sanding Flap DiscsOperation LOCK-ON Button SwitchesSoft Start Feature Paddle SwitchEdge Grinding with Grinding Wheels Mounting Sanding Backing Pads Using Sanding Backing PadsSurface Finishing with Sanding Flap Discs Using Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsMounting Wire Brushes and Wire Wheels Mounting Cutting Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Lubrication MaintenanceCleaning Accessories Using Cutting WheelsSeguridad Eléctrica Definiciones Normas De seguridadSeguridad DEL Área DE Trabajo USO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalMantenimiento Instrucciones DE Seguridad Para Todas LAS OperacionesNormas Específicas DE Seguridad Español Antes DE Atención Colocar LO Siguiente Causas del retroceso y su prevención por parte del operadorEspañol Ténsion Volts Longitud del cable en metros m USO Previsto Descripción FIGComponentes Fig Rotación de la caja de engranajes Protección Contra Sobrecarga POWER-OFFEnsamblado Y Ajustes CaracterísticasMontaje Y Extracción DEL Protector AccesoriosProtector de montaje Cierre el cerrojo del protector para asegurar el mismo a Discos de lijar Discos de corte de 115 mm 2 y 125 mmDiscos de alambre Función DE Arranque Suave InterruptoresFuncionamiento Montaje Y Extracción DE Discos CON Cubo Interruptor DE PaletaBotón DE Bloqueo Bloqueo DEL EJEEsmerilado DE Bordes CON Discos DE Esmerilar Montaje DE Discos SIN CuboEsmerilado DE Superficie CON Discos DE Esmerilar Montaje DE LAS Almohadillas DE Respaldo Para Lijar Acabado DE Superficies CON Discos DE LijarUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de cepillos de alambre y discos de alambreMontaje DEL Protector Cerrado Tipo Montaje y uso de discos de corte TipoUSO DE Ruedas DE Corte MantenimientoMontaje DE LOS Discos DE Corte Limpieza LubricaciónGuarde Estas Instruções Definições Diretrizes de SegurançaRegras Gerais de Segurança Reparos USO E Cuidados DA FerramentaUSE Sempre Proteção Para OS Olhos AO Usar Esta Ferramenta Instruções DE Segurança EspecíficasCausas de retrocesso e prevenção do operador Tensão Comprimento do cabo de extensão USO Devido DA Ferramenta Descrição FIGAcessórios Proteção Contra Sobrecarga POWER-OFFMontagem E Ajustes Rotação da caixa de engrenagemMontagem E Remoção do Protetor Montagem do protetorDiscos de Lixar Discos de Arame de AçoFuncionamento Discos de Lixar de 4-1/2 eInterruptor DE Bloqueio Protetores e FlangesInterruptor DE Palheta Função DE Arranque SuaveMontagem DE Discos SEM Cubos Bloqueio do EixoMontage E Remoção DE Discos do Cubo Esmerilhamento DE Superfície COM Discos DE Esmerilhamento Esmerilhamento DE Superfície COM Discos DE EsmerilharUSO DE Almofadas DE Bloqueio DE Lixar Acabamento DE Superfície COM Discos DE LixaMontagem DAS Almofadas DE Bloqueio DE Lixar USO DE Escovas DE Copo DE FIO E Discos DE ARO Montagem e uso de escovas de fio de aço e discos de aroMontagem DE Escovas DE FIO DE AÇO E Discos DE ARO Montagem DE Protetor Fechado Tipo Montagem e uso de discos de corte TipoMontagem DE Disco DE Corte ManutençãoLubrificação LimpezaEspecificações Page Page Page JUN10 Part No. N082734 D28114 Copyright @ 2009, 2010 D Ewalt

D28114R specifications

The DeWalt D28114R is a powerful and versatile angle grinder designed for both professional and DIY applications. Engineered with a strong focus on performance and durability, this tool stands out in the crowded landscape of power tools. With a robust 12-amp motor, the D28114R generates an impressive no-load speed of up to 11,000 RPM, allowing users to tackle tough materials with ease. Whether grinding, cutting, or polishing, this grinder provides the power and efficiency needed for a variety of tasks.

One of the standout features of the DeWalt D28114R is its innovative dust ejection system. This technology helps to protect the motor and bearings from debris, which can extend the tool's lifespan and maintain optimal performance. The grinder's design includes a sealed switch, which prevents dust and debris from entering and damaging the internal components, ensuring long-lasting functionality.

The D28114R also prioritizes user comfort and safety. Its two-position side handle provides extra control and flexibility during use, accommodating both left- and right-handed users. Additionally, the tool features a lock-on switch for extended grinding sessions, allowing users to operate the grinder comfortably without constant pressure on the trigger.

Durability is a key characteristic of the DeWalt D28114R. Its high-quality construction features a heavy-duty housing that can withstand the rigors of demanding jobs. The grinder is designed to handle tough conditions, making it a reliable choice for construction sites and workshops alike.

Another notable feature of the D28114R is its quick-change wheel release, which allows users to easily switch out grinding wheels and accessories without the need for additional tools. This feature enhances productivity and minimizes downtime during projects.

Moreover, the D28114R is compatible with a variety of wheels and attachments, making it an adaptable tool for various applications. From cutting metal to grinding welds, this angle grinder is equipped to handle every job.

In summary, the DeWalt D28114R angle grinder combines power, durability, and user-friendly features, making it a top choice among professionals and DIY enthusiasts. With its powerful motor, innovative dust ejection system, and emphasis on safety, this tool delivers reliable performance in a versatile and convenient package. Whether you are a seasoned tradesperson or a weekend warrior, the D28114R is designed to exceed your expectations and enhance your productivity on the job.
Top Page Image Contents