DeWalt D28114R instruction manual Mounting and Using Wire Brushes and Wire Wheels

Page 15
5˚-10˚

Begin with coarse grit discs for fast, rough material removal. Move to a medium grit paper and finish with a fine grit disc for optimal finish.

Coarse

16 - 30 grit

Medium

36 - 80 grit

Fine Finishing

100 - 120 grit

Very Fine Finishing

150 - 180 grit

1.Allow the tool to reach full speed before touching tool to the work surface.

2.Apply minimum pressure to work surface, allowing the tool to operate at high speed. Sanding rate is greatest when the tool operates at high speed.

3. Maintain a 5˚ to 15˚ angle between

 

the tool and work surface. The sanding

 

disc should contact approximately one

 

inch of work surface.

5˚-15˚

4.Move the tool constantly in a straight line to prevent burning and swirling

of work surface. Allowing the tool to rest on the work surface without moving, or moving the tool in a circular motion causes burning and swirling marks on the work surface.

5.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before laying it down.

Mounting and Using Wire Brushes and Wire Wheels

Wire cup brushes or wire wheels screw directly on the grinder spindle without the use of flanges. Use only wire brushes or wheels provided with a 5/8-11 threaded hub. A Type 27 guard is required when using wire brushes and wheels.

CAUTION: Wear work gloves when handling wire brushes and wheels. They can become sharp.

CAUTION: Wheel or brush must not touch guard when mounted or while in use. Undetectable damage could occur to the accessory, causing wires to fragment from accessory wheel or cup.

MOUNTING WIRE BRUSHES AND WIRE WHEELS

WARNING: Turn off and unplug the tool before making any adjustments or removing or installing attachments or accessories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off.

1.Thread the wheel on the spindle by hand.

2.Depress spindle lock button and use a wrench on the hub of the wire wheel or brush to tighten the wheel.

3.To remove the wheel, reverse the above procedure.

CAUTION: Failure to properly seat the wheel hub before turning the tool on may result in damage to tool or wheel.

USING WIRE CUP BRUSHES AND WIRE WHEELS

Wire wheels and brushes can be used for removing rust, scale and paint, and for smoothing irregular surfaces.

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to work surface, allowing the tool to operate at high speed. Material removal rate is greatest when the tool operates at high speed.

3. Maintain a 5˚ to 10˚ angle between the tool and work surface for wire cup brushes.

4. Maintain contact between the edge of the wheel and the work surface with wire wheels.

5.Continuously move the tool in a forward and backward motion to avoid creating gouges in the work surface. Allowing the tool to rest on the work surface without moving, or moving the tool in a circular motion causes burning and swirling marks on the work surface.

English

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Esmerilhador de Ângulo Pequeno 115 mm/125 mm 4-1/2/5 Page Electrical Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Work Area SafetyService Specific Safety RulesAdditional Specific Safety Instructions for Grinders Power Tool USE and CareCauses and Operator Prevention of Kickback Always Wear EYE Protection When Using this ToolVoltage Volts Total length of cord in meters m Intended USE Description FIGRotating the Gear Case FeaturesAssembly and Adjustments Accessories2 and 5 Grinding Wheels Mounting GuardMounting and Removing Guard Sanding Discs Wire Wheels2and 5 Sanding Flap Discs OperationGuards and Flanges LOCK-ON Button SwitchesSoft Start Feature Paddle SwitchEdge Grinding with Grinding Wheels Using Sanding Backing Pads Surface Finishing with Sanding Flap DiscsMounting Sanding Backing Pads Mounting and Using Wire Brushes and Wire Wheels Mounting Wire Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 Wheels Mounting Closed Type 1 GuardMounting Cutting Wheels Lubrication MaintenanceCleaning Accessories Using Cutting WheelsDefiniciones Normas De seguridad Seguridad DEL Área DE TrabajoSeguridad Eléctrica USO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalMantenimiento Instrucciones DE Seguridad Para Todas LAS OperacionesNormas Específicas DE Seguridad Español Antes DE Atención Colocar LO Siguiente Causas del retroceso y su prevención por parte del operadorEspañol Ténsion Volts Longitud del cable en metros m Descripción FIG Componentes FigUSO Previsto Rotación de la caja de engranajes Protección Contra Sobrecarga POWER-OFFEnsamblado Y Ajustes CaracterísticasAccesorios Protector de montajeMontaje Y Extracción DEL Protector Cierre el cerrojo del protector para asegurar el mismo a Discos de corte de 115 mm 2 y 125 mm Discos de alambreDiscos de lijar Interruptores FuncionamientoFunción DE Arranque Suave Montaje Y Extracción DE Discos CON Cubo Interruptor DE PaletaBotón DE Bloqueo Bloqueo DEL EJEMontaje DE Discos SIN Cubo Esmerilado DE Superficie CON Discos DE EsmerilarEsmerilado DE Bordes CON Discos DE Esmerilar Montaje DE LAS Almohadillas DE Respaldo Para Lijar Acabado DE Superficies CON Discos DE LijarUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de cepillos de alambre y discos de alambreMontaje DEL Protector Cerrado Tipo Montaje y uso de discos de corte TipoMantenimiento Montaje DE LOS Discos DE CorteUSO DE Ruedas DE Corte Limpieza LubricaciónDefinições Diretrizes de Segurança Regras Gerais de SegurançaGuarde Estas Instruções Reparos USO E Cuidados DA FerramentaUSE Sempre Proteção Para OS Olhos AO Usar Esta Ferramenta Instruções DE Segurança EspecíficasCausas de retrocesso e prevenção do operador Tensão Comprimento do cabo de extensão USO Devido DA Ferramenta Descrição FIGAcessórios Proteção Contra Sobrecarga POWER-OFFMontagem E Ajustes Rotação da caixa de engrenagemMontagem E Remoção do Protetor Montagem do protetorDiscos de Lixar Discos de Arame de AçoFuncionamento Discos de Lixar de 4-1/2 eInterruptor DE Bloqueio Protetores e FlangesInterruptor DE Palheta Função DE Arranque SuaveBloqueio do Eixo Montage E Remoção DE Discos do CuboMontagem DE Discos SEM Cubos Esmerilhamento DE Superfície COM Discos DE Esmerilhamento Esmerilhamento DE Superfície COM Discos DE EsmerilharAcabamento DE Superfície COM Discos DE Lixa Montagem DAS Almofadas DE Bloqueio DE LixarUSO DE Almofadas DE Bloqueio DE Lixar Montagem e uso de escovas de fio de aço e discos de aro Montagem DE Escovas DE FIO DE AÇO E Discos DE AROUSO DE Escovas DE Copo DE FIO E Discos DE ARO Montagem DE Protetor Fechado Tipo Montagem e uso de discos de corte TipoMontagem DE Disco DE Corte ManutençãoLubrificação LimpezaEspecificações Page Page Page JUN10 Part No. N082734 D28114 Copyright @ 2009, 2010 D Ewalt

D28114R specifications

The DeWalt D28114R is a powerful and versatile angle grinder designed for both professional and DIY applications. Engineered with a strong focus on performance and durability, this tool stands out in the crowded landscape of power tools. With a robust 12-amp motor, the D28114R generates an impressive no-load speed of up to 11,000 RPM, allowing users to tackle tough materials with ease. Whether grinding, cutting, or polishing, this grinder provides the power and efficiency needed for a variety of tasks.

One of the standout features of the DeWalt D28114R is its innovative dust ejection system. This technology helps to protect the motor and bearings from debris, which can extend the tool's lifespan and maintain optimal performance. The grinder's design includes a sealed switch, which prevents dust and debris from entering and damaging the internal components, ensuring long-lasting functionality.

The D28114R also prioritizes user comfort and safety. Its two-position side handle provides extra control and flexibility during use, accommodating both left- and right-handed users. Additionally, the tool features a lock-on switch for extended grinding sessions, allowing users to operate the grinder comfortably without constant pressure on the trigger.

Durability is a key characteristic of the DeWalt D28114R. Its high-quality construction features a heavy-duty housing that can withstand the rigors of demanding jobs. The grinder is designed to handle tough conditions, making it a reliable choice for construction sites and workshops alike.

Another notable feature of the D28114R is its quick-change wheel release, which allows users to easily switch out grinding wheels and accessories without the need for additional tools. This feature enhances productivity and minimizes downtime during projects.

Moreover, the D28114R is compatible with a variety of wheels and attachments, making it an adaptable tool for various applications. From cutting metal to grinding welds, this angle grinder is equipped to handle every job.

In summary, the DeWalt D28114R angle grinder combines power, durability, and user-friendly features, making it a top choice among professionals and DIY enthusiasts. With its powerful motor, innovative dust ejection system, and emphasis on safety, this tool delivers reliable performance in a versatile and convenient package. Whether you are a seasoned tradesperson or a weekend warrior, the D28114R is designed to exceed your expectations and enhance your productivity on the job.
Top Page Image Contents