DeWalt D28114R instruction manual Voltage Volts Total length of cord in meters m

Page 6

English

•When restarting a cut-off tool in the workpiece, check that the wheel is not engaged into the material. If wheel is binding, it may walk up or kickback from the workpiece as the tool is restarted.

•Support large panels to minimize the risk of wheel pinching and kickback. Large panels tend to sag under their own weight. Support must be placed under the panel on both sides, near the line of cut and near the edge of the panel.

CAUTION: Use extra care when working into a corner because a sudden, sharp movement of the grinder may be experienced when the wheel or other accessory contacts a secondary surface or a surface edge.

•An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

Voltage (Volts)

Total length of cord in meters (m)

 

 

 

 

 

 

 

 

120

- 127V

0 - 7

 

7 - 15

15 - 30

 

30 - 50

220

- 240V

0 - 15

 

15 - 30

30 - 60

60 - 100

 

 

 

 

 

Rated Ampere

Minimal cross-sectional area of the

range

 

cord in meters (mm2 )

 

0

- 6A

1.0

 

1.5

1.5

 

2.5

6

- 10A

1.0

 

1.5

2.5

 

4.0

10

- 12A

1.5

 

1.5

2.5

 

4.0

12

- 16A

2.5

 

4.0

Not Recommended

WARNING: Always use eye protection. All users and bystanders must wear eye protection that conforms to ANSI Z87.1.

WARNING: Always wear proper personal hearing protection that conforms to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

•ANSI Z87.1 eye protection (CAN/CSA Z94.3),

•ANSI S12.6 (S3.19) hearing protection,

•NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•lead from lead-based paints,

•crystalline silica from bricks and cement and other masonry products, and

•arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Esmerilhador de Ângulo Pequeno 115 mm/125 mm 4-1/2/5 Page Work Area Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Electrical SafetyPower Tool USE and Care Specific Safety RulesAdditional Specific Safety Instructions for Grinders ServiceAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of KickbackVoltage Volts Total length of cord in meters m Description FIG Intended USEAccessories FeaturesAssembly and Adjustments Rotating the Gear Case2 and 5 Grinding Wheels Mounting GuardMounting and Removing Guard Wire Wheels Sanding Discs2and 5 Sanding Flap Discs OperationGuards and Flanges Paddle Switch SwitchesSoft Start Feature LOCK-ON ButtonEdge Grinding with Grinding Wheels Using Sanding Backing Pads Surface Finishing with Sanding Flap DiscsMounting Sanding Backing Pads Mounting and Using Wire Brushes and Wire Wheels Mounting Wire Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Mounting and Using Cutting Type 1 Wheels Mounting Closed Type 1 GuardMounting Cutting Wheels Using Cutting Wheels MaintenanceCleaning Accessories LubricationDefiniciones Normas De seguridad Seguridad DEL Área DE TrabajoSeguridad Eléctrica Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaInstrucciones DE Seguridad Para Todas LAS Operaciones MantenimientoNormas Específicas DE Seguridad Español Causas del retroceso y su prevención por parte del operador Antes DE Atención Colocar LO SiguienteEspañol Ténsion Volts Longitud del cable en metros m Descripción FIG Componentes FigUSO Previsto Características Protección Contra Sobrecarga POWER-OFFEnsamblado Y Ajustes Rotación de la caja de engranajesAccesorios Protector de montajeMontaje Y Extracción DEL Protector Cierre el cerrojo del protector para asegurar el mismo a Discos de corte de 115 mm 2 y 125 mm Discos de alambreDiscos de lijar Interruptores FuncionamientoFunción DE Arranque Suave Bloqueo DEL EJE Interruptor DE PaletaBotón DE Bloqueo Montaje Y Extracción DE Discos CON CuboMontaje DE Discos SIN Cubo Esmerilado DE Superficie CON Discos DE EsmerilarEsmerilado DE Bordes CON Discos DE Esmerilar Acabado DE Superficies CON Discos DE Lijar Montaje DE LAS Almohadillas DE Respaldo Para LijarMontaje y uso de cepillos de alambre y discos de alambre USO DE Almohadillas DE Respaldo Para LijarMontaje y uso de discos de corte Tipo Montaje DEL Protector Cerrado TipoMantenimiento Montaje DE LOS Discos DE CorteUSO DE Ruedas DE Corte Lubricación LimpiezaDefinições Diretrizes de Segurança Regras Gerais de SegurançaGuarde Estas Instruções USO E Cuidados DA Ferramenta ReparosInstruções DE Segurança Específicas USE Sempre Proteção Para OS Olhos AO Usar Esta FerramentaCausas de retrocesso e prevenção do operador Tensão Comprimento do cabo de extensão Descrição FIG USO Devido DA FerramentaRotação da caixa de engrenagem Proteção Contra Sobrecarga POWER-OFFMontagem E Ajustes AcessóriosMontagem do protetor Montagem E Remoção do ProtetorDiscos de Arame de Aço Discos de LixarDiscos de Lixar de 4-1/2 e FuncionamentoFunção DE Arranque Suave Protetores e FlangesInterruptor DE Palheta Interruptor DE BloqueioBloqueio do Eixo Montage E Remoção DE Discos do CuboMontagem DE Discos SEM Cubos Esmerilhamento DE Superfície COM Discos DE Esmerilhar Esmerilhamento DE Superfície COM Discos DE EsmerilhamentoAcabamento DE Superfície COM Discos DE Lixa Montagem DAS Almofadas DE Bloqueio DE LixarUSO DE Almofadas DE Bloqueio DE Lixar Montagem e uso de escovas de fio de aço e discos de aro Montagem DE Escovas DE FIO DE AÇO E Discos DE AROUSO DE Escovas DE Copo DE FIO E Discos DE ARO Montagem e uso de discos de corte Tipo Montagem DE Protetor Fechado TipoLimpeza ManutençãoLubrificação Montagem DE Disco DE CorteEspecificações Page Page Page JUN10 Part No. N082734 D28114 Copyright @ 2009, 2010 D Ewalt

D28114R specifications

The DeWalt D28114R is a powerful and versatile angle grinder designed for both professional and DIY applications. Engineered with a strong focus on performance and durability, this tool stands out in the crowded landscape of power tools. With a robust 12-amp motor, the D28114R generates an impressive no-load speed of up to 11,000 RPM, allowing users to tackle tough materials with ease. Whether grinding, cutting, or polishing, this grinder provides the power and efficiency needed for a variety of tasks.

One of the standout features of the DeWalt D28114R is its innovative dust ejection system. This technology helps to protect the motor and bearings from debris, which can extend the tool's lifespan and maintain optimal performance. The grinder's design includes a sealed switch, which prevents dust and debris from entering and damaging the internal components, ensuring long-lasting functionality.

The D28114R also prioritizes user comfort and safety. Its two-position side handle provides extra control and flexibility during use, accommodating both left- and right-handed users. Additionally, the tool features a lock-on switch for extended grinding sessions, allowing users to operate the grinder comfortably without constant pressure on the trigger.

Durability is a key characteristic of the DeWalt D28114R. Its high-quality construction features a heavy-duty housing that can withstand the rigors of demanding jobs. The grinder is designed to handle tough conditions, making it a reliable choice for construction sites and workshops alike.

Another notable feature of the D28114R is its quick-change wheel release, which allows users to easily switch out grinding wheels and accessories without the need for additional tools. This feature enhances productivity and minimizes downtime during projects.

Moreover, the D28114R is compatible with a variety of wheels and attachments, making it an adaptable tool for various applications. From cutting metal to grinding welds, this angle grinder is equipped to handle every job.

In summary, the DeWalt D28114R angle grinder combines power, durability, and user-friendly features, making it a top choice among professionals and DIY enthusiasts. With its powerful motor, innovative dust ejection system, and emphasis on safety, this tool delivers reliable performance in a versatile and convenient package. Whether you are a seasoned tradesperson or a weekend warrior, the D28114R is designed to exceed your expectations and enhance your productivity on the job.
Top Page Image Contents