DeWalt D28114R Features, Assembly and Adjustments, Rotating the Gear Case, Accessories

Page 8

English

FEATURES

E-SWITCH PROTECTION™

The ON/OFF switch has a no-volt release function. In the event of a power outage or other unexpected shut down, the switch needs to be cycled (turned off and on) to restart tool.

E-CLUTCH™

This unit is equipped with an E-Clutch™ (Electronic Clutch), which in the event of a high-load or wheel pinch, the unit will shut off to reduce the reaction torque to the user. The switch needs to be cycled (turned off and on) to restart the tool.

POWER-OFF™ OVERLOAD PROTECTION

The power supply to the motor will be reduced in case of motor overload. With continued motor overload, the tool will shut off. The switch must be cycled (turned off and on) to restart tool. The power will return to normal once the tool has cooled down to a suitable operating temperature. NOTE: Run the tool at no load to reduce the cool down time.

COMPLETE ELECTRONIC CONTROL™

The internal electronic speed control offers consistent wheel speed while using the tool.

ASSEMBLY AND ADJUSTMENTS

WARNING: Turn off and unplug tool before making any adjustments or removing or

installing accessories. Before reconnecting E the tool, depress and release the trigger switch to ensure that the tool is off.

ATTACHING SIDE HANDLE

The side handle (E) can be fitted to either side of the gear case in the threaded holes, as shown. Before using the tool, check that the handle is tightened securely. Use a wrench to firmly tighten the side handle.

Rotating the Gear Case

1.Remove guard and flanges from tool.

2.Remove the four corner screws attaching the gear case to motor housing.

3.Separating the gear case from motor housing not more than 1/4", rotate the gear case head to desired position.

NOTE: If the gear case and motor housing become separated by more than 1/4", the tool must be serviced and re-assembled by a DEWALT service center. Failure to have the tool serviced may cause brush, motor and bearing failure.

4.Re-install screws to attach the gear case to the motor housing. Tighten screws to 18 in./lbs. torque. Overtightening could cause screws to strip.

5.Re-install guard and correct flanges for the appropriate accessories.

Accessories

It is important to choose the correct guards, backing pads and flanges to use with grinder accessories. See pages 7–9 for information on choosing the correct accessories.

WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated accessory speed may burst and cause injury. Threaded accessories must have a 5/8-11 hub. Every unthreaded accessory must have a 7/8" arbor hole. If it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 7–9 of this manual. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Esmerilhador de Ângulo Pequeno 115 mm/125 mm 4-1/2/5 Page Definitions Safety Guidelines General Power Tool Safety WarningsWork Area Safety Electrical SafetySpecific Safety Rules Additional Specific Safety Instructions for GrindersPower Tool USE and Care ServiceAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of KickbackVoltage Volts Total length of cord in meters m Description FIG Intended USEFeatures Assembly and AdjustmentsAccessories Rotating the Gear CaseMounting and Removing Guard 2 and 5 Grinding WheelsMounting Guard Wire Wheels Sanding DiscsGuards and Flanges 2and 5 Sanding Flap DiscsOperation Switches Soft Start FeaturePaddle Switch LOCK-ON ButtonEdge Grinding with Grinding Wheels Mounting Sanding Backing Pads Using Sanding Backing PadsSurface Finishing with Sanding Flap Discs Using Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsMounting Wire Brushes and Wire Wheels Mounting Cutting Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Maintenance Cleaning AccessoriesUsing Cutting Wheels LubricationSeguridad Eléctrica Definiciones Normas De seguridadSeguridad DEL Área DE Trabajo Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaInstrucciones DE Seguridad Para Todas LAS Operaciones MantenimientoNormas Específicas DE Seguridad Español Causas del retroceso y su prevención por parte del operador Antes DE Atención Colocar LO SiguienteEspañol Ténsion Volts Longitud del cable en metros m USO Previsto Descripción FIGComponentes Fig Protección Contra Sobrecarga POWER-OFF Ensamblado Y AjustesCaracterísticas Rotación de la caja de engranajesMontaje Y Extracción DEL Protector AccesoriosProtector de montaje Cierre el cerrojo del protector para asegurar el mismo a Discos de lijar Discos de corte de 115 mm 2 y 125 mmDiscos de alambre Función DE Arranque Suave InterruptoresFuncionamiento Interruptor DE Paleta Botón DE BloqueoBloqueo DEL EJE Montaje Y Extracción DE Discos CON CuboEsmerilado DE Bordes CON Discos DE Esmerilar Montaje DE Discos SIN CuboEsmerilado DE Superficie CON Discos DE Esmerilar Acabado DE Superficies CON Discos DE Lijar Montaje DE LAS Almohadillas DE Respaldo Para LijarMontaje y uso de cepillos de alambre y discos de alambre USO DE Almohadillas DE Respaldo Para LijarMontaje y uso de discos de corte Tipo Montaje DEL Protector Cerrado TipoUSO DE Ruedas DE Corte MantenimientoMontaje DE LOS Discos DE Corte Lubricación LimpiezaGuarde Estas Instruções Definições Diretrizes de SegurançaRegras Gerais de Segurança USO E Cuidados DA Ferramenta ReparosInstruções DE Segurança Específicas USE Sempre Proteção Para OS Olhos AO Usar Esta FerramentaCausas de retrocesso e prevenção do operador Tensão Comprimento do cabo de extensão Descrição FIG USO Devido DA FerramentaProteção Contra Sobrecarga POWER-OFF Montagem E AjustesRotação da caixa de engrenagem AcessóriosMontagem do protetor Montagem E Remoção do ProtetorDiscos de Arame de Aço Discos de LixarDiscos de Lixar de 4-1/2 e FuncionamentoProtetores e Flanges Interruptor DE PalhetaFunção DE Arranque Suave Interruptor DE BloqueioMontagem DE Discos SEM Cubos Bloqueio do EixoMontage E Remoção DE Discos do Cubo Esmerilhamento DE Superfície COM Discos DE Esmerilhar Esmerilhamento DE Superfície COM Discos DE EsmerilhamentoUSO DE Almofadas DE Bloqueio DE Lixar Acabamento DE Superfície COM Discos DE LixaMontagem DAS Almofadas DE Bloqueio DE Lixar USO DE Escovas DE Copo DE FIO E Discos DE ARO Montagem e uso de escovas de fio de aço e discos de aroMontagem DE Escovas DE FIO DE AÇO E Discos DE ARO Montagem e uso de discos de corte Tipo Montagem DE Protetor Fechado TipoManutenção LubrificaçãoLimpeza Montagem DE Disco DE CorteEspecificações Page Page Page JUN10 Part No. N082734 D28114 Copyright @ 2009, 2010 D Ewalt

D28114R specifications

The DeWalt D28114R is a powerful and versatile angle grinder designed for both professional and DIY applications. Engineered with a strong focus on performance and durability, this tool stands out in the crowded landscape of power tools. With a robust 12-amp motor, the D28114R generates an impressive no-load speed of up to 11,000 RPM, allowing users to tackle tough materials with ease. Whether grinding, cutting, or polishing, this grinder provides the power and efficiency needed for a variety of tasks.

One of the standout features of the DeWalt D28114R is its innovative dust ejection system. This technology helps to protect the motor and bearings from debris, which can extend the tool's lifespan and maintain optimal performance. The grinder's design includes a sealed switch, which prevents dust and debris from entering and damaging the internal components, ensuring long-lasting functionality.

The D28114R also prioritizes user comfort and safety. Its two-position side handle provides extra control and flexibility during use, accommodating both left- and right-handed users. Additionally, the tool features a lock-on switch for extended grinding sessions, allowing users to operate the grinder comfortably without constant pressure on the trigger.

Durability is a key characteristic of the DeWalt D28114R. Its high-quality construction features a heavy-duty housing that can withstand the rigors of demanding jobs. The grinder is designed to handle tough conditions, making it a reliable choice for construction sites and workshops alike.

Another notable feature of the D28114R is its quick-change wheel release, which allows users to easily switch out grinding wheels and accessories without the need for additional tools. This feature enhances productivity and minimizes downtime during projects.

Moreover, the D28114R is compatible with a variety of wheels and attachments, making it an adaptable tool for various applications. From cutting metal to grinding welds, this angle grinder is equipped to handle every job.

In summary, the DeWalt D28114R angle grinder combines power, durability, and user-friendly features, making it a top choice among professionals and DIY enthusiasts. With its powerful motor, innovative dust ejection system, and emphasis on safety, this tool delivers reliable performance in a versatile and convenient package. Whether you are a seasoned tradesperson or a weekend warrior, the D28114R is designed to exceed your expectations and enhance your productivity on the job.
Top Page Image Contents