DeWalt D28114R Surface Finishing with Sanding Flap Discs, Mounting Sanding Backing Pads

Page 14

English

be positioned away from the operator. For deeper cutting with a Type 1 cut-off wheel, use a closed, Type 1 guard. See the chart on page 8 for more information. Type 1 guards are available at extra cost from your local dealer or authorized service center.

1.Allow the tool to reach full speed before touching the tool to the work surface.

2. Apply minimum pressure to the work surface, allowing the tool to operate at high speed. Grinding rate is greatest when the tool operates at high speed.

3. Position yourself so that the open-

underside of the wheel is facing away from you.

4. Once a cut is begun and a notch is established in the workpiece, do not

change the angle of the cut. Changing

the angle will cause the wheel to bend and may cause wheel breakage. Edge grinding wheels are not designed to withstand side pressures caused by bending.

5.Remove the tool from the work surface before turning the tool off. Allow the tool to stop rotating before laying it down.

WARNING: Do not use edge grinding/cutting wheels for surface grinding applications because these wheels are not designed for side pressures encountered with surface grinding. Wheel breakage and injury may result.

SURFACE FINISHING WITH SANDING FLAP DISCS

1.Allow the tool to reach full speed before touching the tool to the work surface.

2. Apply minimum pressure to work

 

surface, allowing the tool to operate

 

at high speed. Sanding rate is

5˚-10˚

greatest when the tool operates at

high speed.

 

3.Maintain a 5˚ to 10˚ angle between the tool and work surface.

4.Continuously move the tool in a forward and backward motion to avoid creating gouges in the work surface.

5.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before laying it down.

MOUNTING SANDING BACKING PADS

WARNING: Turn off and unplug the tool before making any adjustments or removing or installing attachments or accessories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off.

CAUTION: Proper guard must be reinstalled for grinding wheel, sanding flap disc, wire brush or wire wheel applications after

sanding applications are complete.

H

S

1. Place or appropriately thread

 

pad backing (R) on the spindle.

2.Place the sanding disc (S) on the backing pad.

3.While depressing spindle lock,

thread clamp nut (H) on spindle,

 

piloting the raised hub on the clamp

 

nut into the center of sanding disc

 

and backing pad.

 

4. Tighten the clamp nut by hand.

R

Then depress the spindle lock

button while turning the sanding disc until the sanding disc and clamp nut are snug.

5.To remove the wheel, grasp and turn the backing pad and sanding pad while depressing the spindle lock button.

USING SANDING BACKING PADS

Choose the proper grit sandpaper for your application. Sandpaper is available in various grits. Coarse grits yield faster material removal rates and a rougher finish. Finer grits yield slower material removal and a smoother finish.

12

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Esmerilhador de Ângulo Pequeno 115 mm/125 mm 4-1/2/5 Page Work Area Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Electrical SafetyPower Tool USE and Care Specific Safety RulesAdditional Specific Safety Instructions for Grinders ServiceAlways Wear EYE Protection When Using this Tool Causes and Operator Prevention of KickbackVoltage Volts Total length of cord in meters m Description FIG Intended USEAccessories FeaturesAssembly and Adjustments Rotating the Gear CaseMounting and Removing Guard 2 and 5 Grinding WheelsMounting Guard Wire Wheels Sanding DiscsGuards and Flanges 2and 5 Sanding Flap DiscsOperation Paddle Switch SwitchesSoft Start Feature LOCK-ON ButtonEdge Grinding with Grinding Wheels Mounting Sanding Backing Pads Using Sanding Backing PadsSurface Finishing with Sanding Flap Discs Using Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsMounting Wire Brushes and Wire Wheels Mounting Cutting Wheels Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard Using Cutting Wheels MaintenanceCleaning Accessories LubricationSeguridad Eléctrica Definiciones Normas De seguridadSeguridad DEL Área DE Trabajo Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaInstrucciones DE Seguridad Para Todas LAS Operaciones MantenimientoNormas Específicas DE Seguridad Español Causas del retroceso y su prevención por parte del operador Antes DE Atención Colocar LO SiguienteEspañol Ténsion Volts Longitud del cable en metros m USO Previsto Descripción FIGComponentes Fig Características Protección Contra Sobrecarga POWER-OFFEnsamblado Y Ajustes Rotación de la caja de engranajesMontaje Y Extracción DEL Protector AccesoriosProtector de montaje Cierre el cerrojo del protector para asegurar el mismo a Discos de lijar Discos de corte de 115 mm 2 y 125 mmDiscos de alambre Función DE Arranque Suave InterruptoresFuncionamiento Bloqueo DEL EJE Interruptor DE PaletaBotón DE Bloqueo Montaje Y Extracción DE Discos CON CuboEsmerilado DE Bordes CON Discos DE Esmerilar Montaje DE Discos SIN CuboEsmerilado DE Superficie CON Discos DE Esmerilar Acabado DE Superficies CON Discos DE Lijar Montaje DE LAS Almohadillas DE Respaldo Para LijarMontaje y uso de cepillos de alambre y discos de alambre USO DE Almohadillas DE Respaldo Para LijarMontaje y uso de discos de corte Tipo Montaje DEL Protector Cerrado TipoUSO DE Ruedas DE Corte MantenimientoMontaje DE LOS Discos DE Corte Lubricación LimpiezaGuarde Estas Instruções Definições Diretrizes de SegurançaRegras Gerais de Segurança USO E Cuidados DA Ferramenta ReparosInstruções DE Segurança Específicas USE Sempre Proteção Para OS Olhos AO Usar Esta FerramentaCausas de retrocesso e prevenção do operador Tensão Comprimento do cabo de extensão Descrição FIG USO Devido DA FerramentaRotação da caixa de engrenagem Proteção Contra Sobrecarga POWER-OFFMontagem E Ajustes AcessóriosMontagem do protetor Montagem E Remoção do ProtetorDiscos de Arame de Aço Discos de LixarDiscos de Lixar de 4-1/2 e FuncionamentoFunção DE Arranque Suave Protetores e FlangesInterruptor DE Palheta Interruptor DE BloqueioMontagem DE Discos SEM Cubos Bloqueio do EixoMontage E Remoção DE Discos do Cubo Esmerilhamento DE Superfície COM Discos DE Esmerilhar Esmerilhamento DE Superfície COM Discos DE EsmerilhamentoUSO DE Almofadas DE Bloqueio DE Lixar Acabamento DE Superfície COM Discos DE LixaMontagem DAS Almofadas DE Bloqueio DE Lixar USO DE Escovas DE Copo DE FIO E Discos DE ARO Montagem e uso de escovas de fio de aço e discos de aroMontagem DE Escovas DE FIO DE AÇO E Discos DE ARO Montagem e uso de discos de corte Tipo Montagem DE Protetor Fechado TipoLimpeza ManutençãoLubrificação Montagem DE Disco DE CorteEspecificações Page Page Page JUN10 Part No. N082734 D28114 Copyright @ 2009, 2010 D Ewalt

D28114R specifications

The DeWalt D28114R is a powerful and versatile angle grinder designed for both professional and DIY applications. Engineered with a strong focus on performance and durability, this tool stands out in the crowded landscape of power tools. With a robust 12-amp motor, the D28114R generates an impressive no-load speed of up to 11,000 RPM, allowing users to tackle tough materials with ease. Whether grinding, cutting, or polishing, this grinder provides the power and efficiency needed for a variety of tasks.

One of the standout features of the DeWalt D28114R is its innovative dust ejection system. This technology helps to protect the motor and bearings from debris, which can extend the tool's lifespan and maintain optimal performance. The grinder's design includes a sealed switch, which prevents dust and debris from entering and damaging the internal components, ensuring long-lasting functionality.

The D28114R also prioritizes user comfort and safety. Its two-position side handle provides extra control and flexibility during use, accommodating both left- and right-handed users. Additionally, the tool features a lock-on switch for extended grinding sessions, allowing users to operate the grinder comfortably without constant pressure on the trigger.

Durability is a key characteristic of the DeWalt D28114R. Its high-quality construction features a heavy-duty housing that can withstand the rigors of demanding jobs. The grinder is designed to handle tough conditions, making it a reliable choice for construction sites and workshops alike.

Another notable feature of the D28114R is its quick-change wheel release, which allows users to easily switch out grinding wheels and accessories without the need for additional tools. This feature enhances productivity and minimizes downtime during projects.

Moreover, the D28114R is compatible with a variety of wheels and attachments, making it an adaptable tool for various applications. From cutting metal to grinding welds, this angle grinder is equipped to handle every job.

In summary, the DeWalt D28114R angle grinder combines power, durability, and user-friendly features, making it a top choice among professionals and DIY enthusiasts. With its powerful motor, innovative dust ejection system, and emphasis on safety, this tool delivers reliable performance in a versatile and convenient package. Whether you are a seasoned tradesperson or a weekend warrior, the D28114R is designed to exceed your expectations and enhance your productivity on the job.
Top Page Image Contents