Epson D28114 On the gear case cover. You should be, Mounting Cutting Wheels, Using Cutting Wheels

Page 15

1. Open the guard latch (M). Align

O

the lugs (N) on the guard with the

 

slots (O) on the gear case.

 

2. Push the guard down until the

 

guard lug engages and rotates

N

freely in the groove on the gear

 

case hub.

 

3. Rotate guard (I) into desired

M

working position. The guard body

 

should be positioned between the

 

spindle and the operator to provide

 

maximum operator protection.

 

4. Close the guard latch to secure the guard

 

on the gear case cover. You should be

 

unable to rotate the guard by hand when

I

the latch is in closed position. If rotation is

 

possible, tighten the adjusting screw (P)

 

with clamp lever in the closed position.

 

Do not operate grinder with a loose

P

guard or clamp lever in open position.

 

5. To remove the guard, open the guard latch, rotate the guard so that the

arrows are aligned and pull up on the guard.

NOTE: If, after a period of time, the guard becomes loose, tighten the adjusting screw (P) with the clamp lever in the closed position.

CAUTION: Do not tighten adjusting screw with clamp lever in open position. Undetectable damage to guard or mounting hub may result.

MOUNTING CUTTING WHEELS

CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off.

CAUTION: Matching diameter threaded backing flange and clamp nut (included with tool) must be used for cutting wheels.

1.Place the unthreaded backing flange on spindle with the raised section (pilot) facing up. The raised section (pilot) on the back- ing flange will be against the wheel when the wheel is installed.

2.Place the wheel on the backing flange, centering the wheel on the raised section (pilot).

3.Install the threaded clamp nut with the raised section (pilot) facing away from the wheel.

4.Depress the spindle lock button and tighten clamp nut with a wrench.

5.To remove the wheel, grasp and turn while depressing the spindle lock button.

USING CUTTING WHEELS

WARNING: Do not use edge grinding/ cutting wheels for surface grinding applications because these wheels are not designed for side pres- sures encountered with surface grinding. Wheel breakage and injury may result.

1. Allow tool to reach full speed before touch- ing tool to work surface.

2. Apply minimum pressure to work surface, allowing tool to operate at high speed. Cutting rate is greatest when the tool oper- ates at high speed.

3.Once a cut is begun and a notch is established in the work- piece, do not change the angle of the cut. Changing the angle will cause the wheel to bend and may cause wheel breakage.

4.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before setting it down.

English

14

Image 15
Contents Guide Dutilisation Manual DE Instrucciones Work Area General Safety Rules For All ToolsElectrical Safety DewaltTool USE and Care Additional Specific Safety Instructions for GrindersPersonal Safety ServiceCauses and Operator Prevention of Kickback Always Wear EYE Protection When Using this ToolFeatures Switch ProtectionClutch D28140, D28144, D28144N Complete Electronic Control POWER-OFF Overload ProtectionComponents Fig ClutchAttaching Side Handle Assembly and Adjustments2 and 5 Grinding Wheels Rotating the Gear CaseSanding Discs Wire WheelsAccessories 2 and 5 Cutting Wheels2 and 5 Sanding Flap Discs Mounting GuardMounting and Removing Guard Guards and Flanges SwitchesSoft Start Feature OperationMounting NON-HUBBED Wheels LOCK-ON Button D28114, D28144Spindle Lock Mounting and Removing Hubbed WheelsOff. Allow the tool to stop rotating before laying it down Edge Grinding with Grinding WheelsSurface Grinding with Grinding Wheels Sures caused by bendingMounting Sanding Backing Pads Using Sanding Backing PadsSurface Finishing with Sanding Flap Discs Creating gouges in the work surfaceUsing Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsMounting and Using Cutting Type 1 Wheels Mounting Wire CUP Brushes and Wire WheelsUsing Cutting Wheels On the gear case cover. You should beMounting Cutting Wheels Lubrication MaintenanceCleaning Accessories Three Year Limited WarrantyEnglish Mesures DE Sécurité Électricité Règles de sécurité GénéralitésConserver CES Directives Aire DE TravailCalibre minimal des cordons de rallonge Tensi on Sécurité PersonnelleUtilisation ET Entretien DE L’OUTIL Entretien Causes de leffet de rebond et prévention par lopérateur Dispositif E-CLUTCH Composant E-SWITCH Protection Protection E-SWITCHCaractéristiques Embrayage Modèles D28140, D28144 ET D28144NFonction Complete Electronic Control Composants figDisques de Ponçage Capot protecteur pourCapot protecteur pour Meule de type Bouton de Brosses métalliques à touret Meules de 114,3 mm et de 127 mm 4-1/2 et 5 poAssemblage DE LA Poignée Latérale AccessoiresAssemblage ET Réglages Capot protecteur pour Meule de typeMontage ET Démontage DU Capot Protecteur Assemblage du capot protecteurFonctionnement Capots protecteurs et bridesFonction DE Démarrage Souple InterrupteursContacteur À Palette Modèles D28114, D28114N, D28144 ET D28144NBroche lorsque loutil est éteint, débranché C Bouton DE VerrouillageModèles D28114 ET D28144 Dispositif DE Verrouillage DE LA BrocheMeulage DE Chant Avec DES Meules Abrasives Assemblage DE Meules Sans MoyeuMm 1/4 po dépaisseur, enfiler lécrou Meulage DE Surface Avec DES Meules AbrasivesAssemblage DES Tampons Pour LE Ponçage Finition DE Surface Avec DES Disques DE Ponçage À LamellesAssemblage et utilisation des brosses métalliques Utilisation DES Tampons Pour LE PonçageGrains très fins pour la finition Utilisation DE Brosses Coniques ET DE BROSSES-BOISSEAU Assemblage et utilisation de disques de Type 1 coupeAssemblage DE Brosses Coniques ET DE BROSSES-BOISSEAU Pour la retirer, inverser la procédure décrite ci-dessusUtilisation DE Disques DE Coupe Assemblage DE Disques DE CoupeRéparations EntretienNettoyage LubrificationGarantie DE Remboursement DE 90 Jours Contrat D’ENTRETIEN Gratuit D’UN ANSeguridad Eléctrica Instrucciones de seguridad generalesConserve Estas Instrucciones Área DE TrabajoSeguridad Personal Calibre mínimo para cordones de extensiónLongitud total del cordón en metros AmperajeServicio Causas del retroceso y su prevención por parte del operador Protección Contra Sobrecarga POWER-OFF CaracterísticasEmbrague D28140, D28144, D28144N Componentes Fig Protector de montaje Ensamblado Y AjustesRotación de la caja de engranajes AccesoriosTuerca de fijación Roscada Disco con cubo Tipo Protector tipo Liberación del disco Quick-changeCon la palanca de la abrazadera en la posición de cerrada Discos de corte de 114,3 mm 2 y 127 mmDiscos de alambre Liberación del disco Quick-changeFunción DE Arranque Suave InterruptoresBotón DE Bloqueo D28114, D28144 Interruptor DE PaletaD28114, D28114N, D28144, D28144N Interruptor Deslizante D28131, D28140Montaje DE Discos SIN Cubo Montaje Y Extracción DE Discos CON CuboEntre la herramienta y la superficie Esmerilado DE Superficie CON Discos DE EsmerilarEsmerilado DE Bordes CON Discos DE Esmerilar Acabado DE Superficies CON Discos DE LijarUSO DE Almohadillas DE Respaldo Para Lijar Montaje DE LAS Almohadillas DE Respaldo Para LijarSuperficie de trabajo Montaje y uso de cepillos de alambre y discos de alambreMontaje y uso de discos de corte Tipo Para los cepillos de alambre con forma de copaMontaje DE LOS Discos DE Corte Montaje DEL Protector Cerrado TipoReparaciones MantenimientoLimpieza LubricaciónGarantía DE Reembolso DE SU Dinero POR 90 Días Garantía limitada por tres añosExcepciones AÑO DE Servicio GratuitoD28140, D28144, D28144N Especificaciones D28114, D28114N, D28131