Epson LOCK-ON Button D28114, D28144, Spindle Lock, Mounting and Removing Hubbed Wheels

Page 11

inward. To stop the tool while operating in continuous mode, press the rear part of the switch and release.

LOCK-ON BUTTON (D28114, D28144)

 

 

 

The lock-on button (J) offers increased

 

 

 

comfort in extended use applications.

 

 

 

To lock the tool on, push the lock-off

 

 

 

lever (B) toward the back of the tool

 

 

 

then depress the paddle switch (A).

 

 

 

With the tool running, depress the lock-

A

B

J

on button (J). The tool will continue to

 

 

 

 

run after the paddle switch is released. To unlock the tool, depress and release the paddle switch. This will cause the tool to stop.

CAUTION: Allow the tool to reach full speed before touching tool to the work surface. Lift the tool from the work surface before turn- ing the tool off.

SPINDLE LOCK

The spindle lock (C) is provided to prevent the spindle from rotat- ing when installing or removing wheels. Operate the spindle lock only when the tool is turned off, unplugged C

from the power supply, and has come to a complete stop. Do not engage the spindle lock while the tool is operating because

damage to the tool will result. To engage the lock, depress the spindle lock button and rotate the spindle until you are unable to rotate the spindle further.

Mounting and Using Depressed Center Grinding Wheels and Sanding Flap Discs

MOUNTING AND REMOVING HUBBED WHEELS

CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, depress and release the paddle switch to ensure that the tool is off.

Hubbed wheels install directly on the 5/8"-11 threaded spindle. Thread of accessory must match thread of spindle.

1.Backing flange is retained to the grinder by an O-ring on the spindle. Remove backing flange by pulling and twisting flange away form the machine.

2.Thread the wheel on the spindle by hand.

3.Depress the spindle lock button and use a wrench to tighten the hub of the wheel.

4.Reverse the above procedure to remove the wheel.

CAUTION: Failure to properly seat the wheel before turning the tool on may result in damage to the tool or the wheel.

MOUNTING NON-HUBBED WHEELS

CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or acces- sories. Before reconnecting the tool, turn the switch on and off as previously described to ensure that the tool is off.

Depressed center Type 27 grinding wheels G1

must be used with included flanges.

 

NOTE: The quick-change wheel release

 

(G1) is for use with for D28114, D25114N

D

and D28131. The stamped steel backing

 

flange (G2) is for use with D28140, D28144

and D28144N. Refer to page 6–8 for more information.

1.Install the unthreaded backing flange (G1) on spindle (D) with the raised section (pilot) against the wheel. Be sure the backing flange recess is seated onto the flats of the spindle by pushing and twisting the flange before placing wheel.

2. Place wheel against the backing flange, centering the wheel on the raised section (pilot) of the backing flange.

3. While

depressing

the spindle lock

 

button,

thread the

clamp nut (H) on

 

H

spindle. If the wheel you are installing is

 

English

10

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Guide Dutilisation Manual DE Instrucciones Work Area General Safety Rules For All ToolsElectrical Safety DewaltTool USE and Care Additional Specific Safety Instructions for GrindersPersonal Safety ServiceCauses and Operator Prevention of Kickback Always Wear EYE Protection When Using this ToolClutch D28140, D28144, D28144N FeaturesSwitch Protection Complete Electronic Control POWER-OFF Overload ProtectionComponents Fig ClutchAttaching Side Handle Assembly and Adjustments2 and 5 Grinding Wheels Rotating the Gear CaseSanding Discs Wire WheelsAccessories 2 and 5 Cutting WheelsMounting and Removing Guard 2 and 5 Sanding Flap DiscsMounting Guard Guards and Flanges SwitchesSoft Start Feature OperationMounting NON-HUBBED Wheels LOCK-ON Button D28114, D28144Spindle Lock Mounting and Removing Hubbed WheelsOff. Allow the tool to stop rotating before laying it down Edge Grinding with Grinding WheelsSurface Grinding with Grinding Wheels Sures caused by bendingMounting Sanding Backing Pads Using Sanding Backing PadsSurface Finishing with Sanding Flap Discs Creating gouges in the work surfaceUsing Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsMounting and Using Cutting Type 1 Wheels Mounting Wire CUP Brushes and Wire WheelsMounting Cutting Wheels Using Cutting WheelsOn the gear case cover. You should be Lubrication MaintenanceCleaning Accessories Three Year Limited WarrantyEnglish Mesures DE Sécurité Électricité Règles de sécurité GénéralitésConserver CES Directives Aire DE TravailUtilisation ET Entretien DE L’OUTIL Calibre minimal des cordons de rallonge Tensi onSécurité Personnelle Entretien Causes de leffet de rebond et prévention par lopérateur Dispositif E-CLUTCH Composant E-SWITCH Protection Protection E-SWITCHCaractéristiques Embrayage Modèles D28140, D28144 ET D28144NFonction Complete Electronic Control Composants figCapot protecteur pour Meule de type Bouton de Disques de PonçageCapot protecteur pour Brosses métalliques à touret Meules de 114,3 mm et de 127 mm 4-1/2 et 5 poAssemblage DE LA Poignée Latérale AccessoiresAssemblage ET Réglages Capot protecteur pour Meule de typeMontage ET Démontage DU Capot Protecteur Assemblage du capot protecteurFonctionnement Capots protecteurs et bridesFonction DE Démarrage Souple InterrupteursContacteur À Palette Modèles D28114, D28114N, D28144 ET D28144NBroche lorsque loutil est éteint, débranché C Bouton DE VerrouillageModèles D28114 ET D28144 Dispositif DE Verrouillage DE LA BrocheMeulage DE Chant Avec DES Meules Abrasives Assemblage DE Meules Sans MoyeuMm 1/4 po dépaisseur, enfiler lécrou Meulage DE Surface Avec DES Meules AbrasivesAssemblage DES Tampons Pour LE Ponçage Finition DE Surface Avec DES Disques DE Ponçage À LamellesGrains très fins pour la finition Assemblage et utilisation des brosses métalliquesUtilisation DES Tampons Pour LE Ponçage Utilisation DE Brosses Coniques ET DE BROSSES-BOISSEAU Assemblage et utilisation de disques de Type 1 coupeAssemblage DE Brosses Coniques ET DE BROSSES-BOISSEAU Pour la retirer, inverser la procédure décrite ci-dessusUtilisation DE Disques DE Coupe Assemblage DE Disques DE CoupeRéparations EntretienNettoyage LubrificationGarantie DE Remboursement DE 90 Jours Contrat D’ENTRETIEN Gratuit D’UN ANSeguridad Eléctrica Instrucciones de seguridad generalesConserve Estas Instrucciones Área DE TrabajoSeguridad Personal Calibre mínimo para cordones de extensiónLongitud total del cordón en metros AmperajeServicio Causas del retroceso y su prevención por parte del operador Embrague D28140, D28144, D28144N Protección Contra Sobrecarga POWER-OFFCaracterísticas Componentes Fig Protector de montaje Ensamblado Y AjustesRotación de la caja de engranajes AccesoriosTuerca de fijación Roscada Disco con cubo Tipo Protector tipo Liberación del disco Quick-changeCon la palanca de la abrazadera en la posición de cerrada Discos de corte de 114,3 mm 2 y 127 mmDiscos de alambre Liberación del disco Quick-changeFunción DE Arranque Suave InterruptoresBotón DE Bloqueo D28114, D28144 Interruptor DE PaletaD28114, D28114N, D28144, D28144N Interruptor Deslizante D28131, D28140Montaje DE Discos SIN Cubo Montaje Y Extracción DE Discos CON CuboEntre la herramienta y la superficie Esmerilado DE Superficie CON Discos DE EsmerilarEsmerilado DE Bordes CON Discos DE Esmerilar Acabado DE Superficies CON Discos DE LijarUSO DE Almohadillas DE Respaldo Para Lijar Montaje DE LAS Almohadillas DE Respaldo Para LijarSuperficie de trabajo Montaje y uso de cepillos de alambre y discos de alambreMontaje y uso de discos de corte Tipo Para los cepillos de alambre con forma de copaMontaje DE LOS Discos DE Corte Montaje DEL Protector Cerrado TipoReparaciones MantenimientoLimpieza LubricaciónGarantía DE Reembolso DE SU Dinero POR 90 Días Garantía limitada por tres añosExcepciones AÑO DE Servicio GratuitoD28140, D28144, D28144N Especificaciones D28114, D28114N, D28131
Top Page Image Contents