Bosch Power Tools 1619EVS Maintenance, Accessories, Tool Lubrication, Carbon Brushes, Bearings

Page 19
! WARNING
! CAUTION
! WARNING

BM2610995777 10/03 10/7/03 4:51 PM Page 19

Maintenance

Service

Preventive maintenance

!WARNING performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station.

TOOL LUBRICATION

The depth rod and coarse ! CAUTION adjustment lock must not be

lubricated or coarse adjustment lock will slip.

Your Bosch tool has been properly lubricated and is ready to use. It is recommended that tools with gears be regreased with a special gear lubricant at every brush change.

CARBON BRUSHES

The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months the brushes be examined. Only genuine Bosch replacement brushes specially designed for your tool should be used.

BEARINGS

After about 300-400 hours of operation, or at every second brush change, the bearings should be replaced at Bosch Factory Service Center or Authorized Bosch Service Station. Bearings which become noisy (due to heavy load or very abrasive material cutting) should be replaced at once to avoid overheating or motor failure.

Cleaning

To avoid accidents always disconnect the tool from the power supply before cleaning or performing

any maintenance. The tool may be cleaned most effectively with compressed dry air.

Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not at- tempt to clean by inserting pointed objects through openings.

Certain cleaning agents and solvents damage plastic parts. Some of these are: gasoline, carbon

tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

Accessories

If an extension cord is necessary, a cord with adequate size conductors that is capable of

carrying the current necessary for your tool must be used. This will prevent excessive voltage drop, loss of power or overheating. Grounded tools must use 3-wire extension cords that have 3-prong plugs and receptacles.

NOTE: The smaller the gauge number, the heavier the cord.

RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT ALTERNATING CURRENT TOOLS

Tool’s

Cord Size in A.W.G.

Wire Sizes in mm2

Ampere

 

 

 

 

 

 

 

 

Cord Length in Feet

Cord Length in Meters

Rating

 

25

50

100

150

15

30

60

120

3-6

 

 

 

 

 

 

 

 

18

16

16

14

0.75

0.75

1.5

2.5

6-8

18

16

14

12

0.75

1.0

2.5

4.0

8-10

18

16

14

12

0.75

1.0

2.5

4.0

10-12

16

16

14

12

1.0

2.5

4.0

—

12-16

14

12

—

—

—

—

—

—

 

 

 

 

 

 

 

 

 

1/4” Collet Chuck *

Adapters for Various

Fine Adjustment Extension *

1/2” Collet Chuck *

Vacuum Hoses *

Metric Coarse Adjustment

24 mm Collet Nut Wrench *

Vacuum Hose **

Indicator **

3/8” Collet Chuck **

Deluxe Router Guide **

 

8 mm Collet Chuck **

Router Bits **

(*= standard equipment)

Dust Extraction Hood with

Templet Guides **

(**= optional accessories)

Enhancement Ring *

Templet Guide Adapters **

 

Dust Extraction Hood for

Centering Cone **

 

Edge Forming **

Router Table **

 

-19-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Importante Work Area Power Tool Safety RulesService Safety Rules for RoutersSafety Rules for Router Table BM2610995777 10/03 10/7/03 451 PM Symbols Router Functional Description and SpecificationsPlunge Lock Override Lever Base SUB-BASE Removing the Router BIT AssemblyInstalling a Router BIT Selecting BitsPlunging Action Installing Templet Guide AdapterOperating Instructions Router Dust CollectionFine Adjustment Indicator Coarse Depth AdjustmentCoarse Adjustment Indicator Fine Adjustment KnobMaking Progessively Deeper Plunge Cuts Electronic Variable Speed Control Trigger Switch and LOCK-ON ButtonSoft Start Feature Dial Setting RPM ApplicationStart Here Work BIT Direction Router Feed Feeding the RouterRate of Feed Edge FormingAttaching Dust Extraction Hood Dust Collection While Edge FormingSecurely Clamp Board Guide Feed Direction Centering the SUB-BASE Templet GuidesDeluxe Router Guide Plunge Lock Lever Coarse Adjustment Lock Spring Defeat ButtonPreparation For Use With Bosch Router Table Plunge LockAttaching Router to Mounting Plate Adjusting the DepthConnect the Router and the Router Table Switch Operation in Router TableCarbon Brushes MaintenanceAccessories Tool LubricationBlessures graves Règles de Sécurité GénéralesConservez CES Instructions Réparation Règles de sécurité concernant les toupiesLe plomb provenant des peintures à base de plomb Consignes de sécurité pour table de toupillageBM2610995777 10/03 10/7/03 451 PM Une vitesse plus grande SymbolesTours ou mouvement alternatif par Position. Un nombre plus élevé signifieDéfonceuse Description fonctionnelle et spécificationsPour Enlever UN FER DE Défonceuse AssemblageChoix DES Fers Montage DES FersMouvement DE Plongée Installation DE L’ADAPTATEUR DE Guide DE GabaritConsignes d’utilisation Ramassage DES PoussièresIndex DE Réglage FIN Réglage Grossier DE LA ProfondeurIndex DE Réglage Grossier Bouton DE Réglage FINAugmentation Progressive DE LA Profondeur DE Coupe TR/MIN Application Commande Électronique DE Variation DE VitesseGchette ET Bouton DE Verrouillage SUR Marche Système DE Démarrage ProgressifChant de bout endommage la pièce Avance DE LA DéfonceuseVitesse D’AVANCE Moulurage DE ChantsCapuchon ’EXTRACTION DE Poussière Ramassage DE Poussière Lors DU Moulurage DE ChantsFixation DU Capuchon D’EXTRACTION DE Poussière Chant DE LA PièceDE LA Défonceuse Centrage DE LA SOUS-EMBASE ET DES Guides DE GabaritBridez Fermement LA Planche DE Guidage Sens DE ’AVANCE Désirée Tiges DU Guide Déport PièceSens DE ’AVANCE VIS Moletée Embase CoupeProfondeur Levier DE Préparation pour utilisation avec la table de toupillageSens DE L’AVANCE DE LA Pièce Utilisation avec la table de toupillageDE Montage Réglage DE LA ProfondeurBalais OU Charbons AccessoiresEntretien Lubrification DE L’OUTILConserve Estas Instrucciones Normas de seguridad para herramientas mecánicasServicio Normas de seguridad para fresadorasInstrucciones de seguridad para la mesa de fresadora BM2610995777 10/03 10/7/03 451 PM Con aislamiento doble SímbolosDe Ni-Cd Intensité nominale 15 a Descripción funcional y especificacionesFresadoras Riesgo de arrancar la herramienta accidentalmenteRemoción DE LA Broca DE Fresadora EnsamblajeSelección DE Brocas Bascule hacia arriba el escudo antivirutasAcción DE Penetración FresadoraCubierta a mangueras de aspiración de 1-1/4 y 1-1/2 Instalación DEL Adaptador DE Guías DE PlantillaIndicador DE Ajuste Fino Ajuste DE Profundidad GruesoIndicador DE Ajuste Grueso Pomo DE Ajuste FinoVarilla DE Profundidad Torreta DE Tope Broca Marca DE Cierre DE Referencia Ajuste GruesoDEL Dial Interruptor Gatillo Y Botón DE Fijación EN EncendidoDispositivo DE Arranque Suave Posición RPMVelocidad DE Avance Avance DE LA FresadoraConformado DE Bordes Cubierta DE Extracción DE Polvo Colocación DE LA Cubierta DE Extracción DE PolvoTornillo Guiado DE LA Fresadora Centrado DE LA Subbase Y LAS Guías DE PlantillaPatrón DE Plantilla Pieza DE Guía DE Fresadora DE LujoBroca DE Guía DE Fresadora PlantillaCierre DE Ajuste Grueso Botón DE Anulación DEL Resorte Preparación para la utilización con la mesa de fresadoraCarcasa Palanca DE DE Penetración Palanca DE Fijación DE LA ProfundidadDE LA Mesa DE Fresadora Utilización en la mesa de fresadoraSujeción DE LA Fresadora a LA Placa DE Montaje Ajuste DE LA ProfundidadEscobillas DE Carbon MantenimientoAccesorios Lubricacion DE LAS HerramientasLimited Warranty of Bosch Portable and Benchtop Power Tools
Related manuals
Manual 64 pages 47.92 Kb
Top Page Image Contents