Panasonic EYFEA1N operating instructions Clutch Lock Cover, Battery Pack For Appropriate Use

Page 11

• Clutch Lock Cover

The clutch lock cover allows you to lock the clutch at the selected setting.

Attaching the cover

1.Select the appropriate clutch setting for the application.

2.Attach the clutch lock cover.

•Align the triangle mark on the cover with the graduation selection mark on the drill and attach.

Triangle mark Graduation selection mark

Tightening the screw to immobilize the cover.

•Use a hand screwdriver. Tightening the screw too much may damage the cover.

Caution: DO NOT STARE INTO BEAM. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Automatic power-off function

●●The automatic power-off function is designed to prevent a loss of tightening torque due to reduced battery voltage. Once it has been activated, the tool will not operate until the battery pack has been charged (or replaced with a fresh unit), even if the trigger is depressed.

●●LED lamp will flash when the automatic power-off function is activated.

●●LED lamp begins flashing, the battery pack should be charged (or replaced with a fresh unit) immediately.

●●Be sure to fully charge the battery pack in question after activation of the automatic power-off function. Failure to do so may prevent the automatic power-off funtion from being properly deactivated.

*Only use the screw that comes with the clutch lock cover.

Removing the cover

1. Remove the clutch lock cover.

LED light

Pull the trigger. The light illuminates with very low current, and it does not adversely affect the performance of the tool during use or its battery capacity.

CAUTION:

●●The built-in LED light is designed to illuminate the small work area tempo- rarily.

●●Do not use it as a substitute for a regular flashlight, since it does not have enough brightness.

- 11 -

[Battery Pack]

For Appropriate Use of

Battery Pack

Li-ion Battery Pack

●●For optimum battery life, store the Li-ion bat- tery pack following use without charging it.

●●When charging the battery pack, confirm that the terminals on the battery charger are free of foreign substances such as dust and water etc. Clean the terminals before charging the battery pack if any foreign substances are found on the terminals.

The life of the battery pack terminals may be affected by foreign substances such as dust and water etc. during operation.

●●When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a con- nection from one terminal to another.

Shorting the battery terminals together may cause sparks, burns or a fire.

●●When operating the battery pack, make sure the work place is well ventilated.

●●When the battery pack is removed from the main body of the tool, replace the battery pack cover immediately in order to prevent dust or dirt from contaminating the battery terminals and causing a short circuit.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model No EYFEA1N Index/Index/Indice Introduction II. General Safety RulesElectrical Safety Personal SafetyBattery Tool Use and Care Power Tool Use and CareService III. Specific Safety RulesImportant Safety Instructions IV. for Battery Charger & Battery PackPage Attaching or Removing Bat- tery Pack AssemblyVI. Operation Attaching or Removing BitClutch Torque Setting Switch and Forward/Reverse Lever OperationForward Rotation Switch Operation Reverse Rotation Switch OperationBit-locking Function How to Use Hook ringUsing Hook Ring Clutch Lock Cover Battery Pack For Appropriate UseBattery Recycling Battery Charger ChargingBattery Pack Life Federal Communication Commission Interference Statement Lamp IndicationsIX. Appendix VII. MaintenanceVIII. Accessories SpecificationsBattery Charger Battery PackConservez CES II. ConsignesDE Secu Rite GeneralesUtilisation et soins de l’outil mécanique Réparation III. Regles DE Securite ParticulieresUtilisation et soins de la batterie de l’outil Avertissement Symbole SignificationInstructions de sécurité importantes IV. Chargeur DE Batterie ET Batterie AutonomeAvertissement Fixation ou retrait de la bat- terie autonome MontageVI. Fonctionnement Fixation ou retrait d’une mècheUtilisation pour le perçage Utilisation du commutateur pour une rotation en sens normalUtilisation du commutateur de rotation en sens inverse Réglage du couple de serrage de l’embrayageMèche Comment utiliser l’anneau’accrochage Fonction de verrouillage de laCouvercle du verrouillage de l’embrayage Utilisation de l’anneau d’accrochageRecyclage de la batterie autonome Fonction d’extinction automatiqueBatterie autonome Li-ion Longévité des batteries autonomesChargeur de batterie Recharge Indication DU Voyant Caracteristiques Techniques VIII. AccessoiresVII. Entretien IX. AppendiceChargeur DE Batterie Batterie AutonomeIntroducción Utilisation et soins de l’outil mécanique III. Regles DE Securite Particulieres Símbolo Significado IV. Chargeur DE Batterie ET Batterie Autonome Avertissement Colocación y extracción de la batería MontajeVI. Funcionamiento Colocación o extracción de la brocaUtilización para taladrar Funcionamiento del interrup- tor de rotación de avanceFuncionamiento del interrup- tor de rotación inversa Ajuste de torsión del embragueAdvertencia Función de bloqueo de brocaCómo utilizar el anillo de gancho Cubierta de bloqueo del embrague Utilizar un anillo de ganchoAtención Bloque de pilasCargador de la batería Carga Nota Indicación DE LA Lámpara Specifiche Tecniche VII. MantenimientoVIII. Accesorios IX. AnexoCargador DE Batería BateríaEN. FR. ES
Top Page Image Contents