Siemens FC330A manual Printer disabling/enabling, When has the printer to be disabled?

Page 48

Printer disabling/enabling

Printer disabling/enabling

i	Printer connected: Yes p	No p

When has the printer to be disabled?

Under normal conditions the printer operates in active stand-by. It is only disabled in special ca- ses e. g. for change of paper or repair.

Disabling the printer

1. Press St .		SELECT:	1.	ENabling
1. Press St .	*	(main menu)	2.	DISabling
Ü Display shows	*		3.	INFO polling
			3.	INFO polling
			4.	other functions
2. Select option 2. ä 3. ä 3. (to disable

		printer DISABLED
the printing of all messages)
Ü Display shows	*	timeout /hm: menu		Stop: end operating
for a few seconds		timeout /hm: menu		Stop: end operating

ÜThe printer is disabled.

ÜThe yellow LED of the display field Isolation is on.

Enabling the printer

1. Press St .
Ü Display shows	*

2.Select option 1. ä 3. ä 1.

Ü Display shows	*
for a few seconds

ÜThe printer is enabled.

SELECT: 1. ENabling (main menu) 2. DISabling

3.INFO polling

4.other functions

printer ACTIVE: log ALL messages

timeout /hm: menu

Stop: end operating

ÜThe yellow LED of the display field Isolation is off, if no other parts of the system are isola- ted.

44

Fire & Security Products	e1973c-13
Siemens Building Technologies Group	02.2004

Image 48

Contents Fire & Security Products PhaseSynova FC330A Fire detection system Operating manual System operation for userECopyright by Siemens Building Technologies AG Overview operating menu Fire & Security Products 06.2003Siemens Building Technologies Group Introduction Fire & Security Productse1973c-1 Siemens Building Technologies GroupPage Fundamentals Fire & Security Productse1973c-2 Siemens Building Technologies GroupControl console layout 1 ALARMControl console FC330A Floor panel B3Q580B3Q590/595 Overview operating menu page 4.other functionsonly for service engineer 4.other functionsFundamental operation How to operate the control consoleNormal operation ALARMWhat is “normal operation”? Mains interruptionOperating access Possible access levelsHow do I get operating access? Operating access via password Log inLog out Operating “manned” and “unmanned” Basic rulesAutomatic switchover Extra timeAlarm Fire & Security Productse1973c-3 Siemens Building Technologies GroupSPECIAL Alarm Concept Purpose and principleAlarm investigation time V1 =V2 = Alarm ALARMPrinciple How are alarm messages shown on the text display? How to respond in case of alarmWhat to do after an alarm Scrolling alarm messagesFire & Security Products e1973c-3Siemens Building Technologies Group 02.2004Disable/Enable System Parts Fire & Security Productse1973c-4 Siemens Building Technologies GroupTemporary isolation of a detector zone What is a detector zone?When has a detector zone to be isolated? Zone isolation procedure Viewing disabled zones Zone reactivation procedureDisable all zones Several zones disabledEnable single zones Enable a range of zonesEnable all disabled zones Temporary isolation of a single detector When has a single detector to be isolated?Single detector isolation procedure Detector reactivation procedure Remote Transmission What is “remote transmission”?When has the remote transmission to be disabled? Disabling the remote alarm transmission facilityDisabling the remote fault transmission facility Enabling the remote fault transmission facilityAlarm devices When have alarm devices to be disabled?Disabling the alarm devices Enabling alarm devicesFaults Fire & Security Productse1973c-7 Siemens Building Technologies GroupFaults How do I respond to fault messages?Reset What remedies are available to the user?Maintenance Fire & Security Productse1973c-8 Siemens Building Technologies GroupDetector test Purpose and PrincipleRecommendations for function tests 4.After entering the last number press ok twice Functional testing of automatic AlgoRex-detectors Test procedure for detector tester RE6Test procedure for detector tester RE6T Required equipementTest procedure for type KAC Test procedure for type DIN indirect activationFunctional test of manual call points Control consoleLamp test Lamp test procedurePurpose of the lamp test Battery load test Battery load test procedurePurpose and principle Test of acoustic alarm devices Horn test procedurePurpose and principle Test of Remote Transmission RT Test procedure for remote alarm transmissionTest procedure for remote fault transmission Purpose and principleFire & Security Products e1973c-12Siemens Building Technologies Group 02.2004Other Functions Fire & Security Productse1973c-13 Siemens Building Technologies GroupPrinter disabling/enabling When has the printer to be disabled?Disabling the printer Enabling the printerPaper replacement with logging printer B2Q191 Switch off the printerEnable the printer Change of printer paperPoll alarm counter Purpose of polling the alarm counterPolling the alarm counter Poll event memory Purpose of polling the event memoryPolling the event memory Poll user text of zones or elements PurposePolling user text of zones or elements Poll system status PurposePolling the system status Poll configuration data Polling configuration data of detector zonesPolling configuration data of address lines PurposePrintout Print event memory/alarm counterPrint configuration/user text Print configuration zone/line/LONSet time and date Purpuse and PrincipleSet time and date Page Siemens Building Technologies AG Alte Landstrasse CH-8708Männedorf Tel. +41 1 −Document no. e1973c Edition