Siemens FC330A manual Remote Transmission, What is “remote transmission”?

Page 32
Remote Transmission

Remote Transmission

i

Remote transmission provided:

No p

Yes p

Alarm to:

 

 

Fault transmission provided:

No p

Yes p

Alarm to:

 

 

 

 

 

 

 

 

 

What is “remote transmission”?

The remote transmission facility establishes a transmission path to the fire department in the event of a fire alarm issued by the fire detection system. Depending on the alarm concept, the alarm is transmitted immediately to the fire department, or after a certain delay, giving time for investigation by operating personnel.

In single cases a separate transmission path for fault messages is established.

When has the remote transmission to be disabled?

Under normal conditions the remote alarm transmission facility is enabled to ensure minimal alarming times. The remote transmission facility is disabled only in special cases to prevent un- necessary turn out of the fire brigade. The transmission facility should be disabled for:

nTest of the fire detection system

nMaintenance and conversion works on the fire detection system

WARNING

When the remote alarm transmission is disabled, no automatic alarm is transmitted to the fire department! Operating personnel must be on the premises to investigate immediately the location in case of an alarm and to alarm the fire department in case of fire!

Disabling the remote alarm transmission facility

1. Press St .

 

Ü Display shows

*

2.Select option 2. ä 2. ä 3.

Ü Display shows

*

3.Enter the desired disabling time or 99 for permanent disabling.

Ü Display shows

*

for a few seconds

 

SELECT: 1. ENabling (main menu) 2. DISabling

3.INFO polling

4.other functions

DISABLE RT−alarm:

> hours DISABLED? (99=permanent)

hm: back to menu

Stop: end operating

 

RT−alarm permanent DISABLED

timeout /hm: menu

Stop: end operating

 

 

ÜThe remote fire alarm transmission is disabled.

ÜThe yellow LEDs of the display fields Isolation and Remote alarm/fault off are on.

ÜThe text display indicates that no alarm message is pending.

Enabling the remote alarm transmission facility

1. Press St .

 

Ü Display shows

*

2.Select option 1. ä 2. ä 3.

Ü Display shows

*

for a few seconds

 

SELECT: 1. ENabling (main menu) 2. DISabling

3.INFO polling

4.other functions

RT−alarm ENABLED

timeout /hm: menu

Stop: end operating

ÜThe remote fire alarm transmission is enabled.

ÜThe yellow LEDs of the display fields Isolation and Remote alarm/fault off are off, if no other parts of the system are isolated.

28

Fire & Security Products

e1973c-5

Siemens Building Technologies Group

02.2004

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Fire & Security Products PhaseSynova FC330A Fire detection system Operating manual System operation for userECopyright by Siemens Building Technologies AG Overview operating menu Siemens Building Technologies Group Fire & Security Products06.2003 Introduction Fire & Security Productse1973c-1 Siemens Building Technologies GroupPage Fundamentals Fire & Security Productse1973c-2 Siemens Building Technologies GroupControl console FC330A Control console layout1 ALARM B3Q590/595 Floor panelB3Q580 Overview operating menu page 4.other functionsonly for service engineer 4.other functionsFundamental operation How to operate the control consoleNormal operation ALARMWhat is “normal operation”? Mains interruptionHow do I get operating access? Operating accessPossible access levels Log out Operating access via passwordLog in Operating “manned” and “unmanned” Basic rulesAutomatic switchover Extra timeAlarm Fire & Security Productse1973c-3 Siemens Building Technologies GroupSPECIAL Alarm Concept Purpose and principleV2 = Alarm investigation timeV1 = Principle AlarmALARM How are alarm messages shown on the text display? How to respond in case of alarmWhat to do after an alarm Scrolling alarm messagesFire & Security Products e1973c-3Siemens Building Technologies Group 02.2004Disable/Enable System Parts Fire & Security Productse1973c-4 Siemens Building Technologies GroupWhen has a detector zone to be isolated? Temporary isolation of a detector zoneWhat is a detector zone? Zone isolation procedure Viewing disabled zones Zone reactivation procedureDisable all zones Several zones disabledEnable all disabled zones Enable single zonesEnable a range of zones Single detector isolation procedure Temporary isolation of a single detectorWhen has a single detector to be isolated? Detector reactivation procedure Remote Transmission What is “remote transmission”?When has the remote transmission to be disabled? Disabling the remote alarm transmission facilityDisabling the remote fault transmission facility Enabling the remote fault transmission facilityAlarm devices When have alarm devices to be disabled?Disabling the alarm devices Enabling alarm devicesFaults Fire & Security Productse1973c-7 Siemens Building Technologies GroupFaults How do I respond to fault messages?Reset What remedies are available to the user?Maintenance Fire & Security Productse1973c-8 Siemens Building Technologies GroupRecommendations for function tests Detector testPurpose and Principle 4.After entering the last number press ok twice Functional testing of automatic AlgoRex-detectors Test procedure for detector tester RE6Test procedure for detector tester RE6T Required equipementTest procedure for type KAC Test procedure for type DIN indirect activationFunctional test of manual call points Control consolePurpose of the lamp test Lamp testLamp test procedure Purpose and principle Battery load testBattery load test procedure Purpose and principle Test of acoustic alarm devicesHorn test procedure Test of Remote Transmission RT Test procedure for remote alarm transmissionTest procedure for remote fault transmission Purpose and principleFire & Security Products e1973c-12Siemens Building Technologies Group 02.2004Other Functions Fire & Security Productse1973c-13 Siemens Building Technologies GroupPrinter disabling/enabling When has the printer to be disabled?Disabling the printer Enabling the printerPaper replacement with logging printer B2Q191 Switch off the printerEnable the printer Change of printer paperPolling the alarm counter Poll alarm counterPurpose of polling the alarm counter Polling the event memory Poll event memoryPurpose of polling the event memory Polling user text of zones or elements Poll user text of zones or elementsPurpose Polling the system status Poll system statusPurpose Poll configuration data Polling configuration data of detector zonesPolling configuration data of address lines PurposePrintout Print event memory/alarm counterPrint configuration/user text Print configuration zone/line/LONSet time and date Set time and datePurpuse and Principle Page Siemens Building Technologies AG Alte Landstrasse CH-8708Männedorf Tel. +41 1 −Document no. e1973c Edition
Top Page Image Contents