Teledyne powerpod 400 instruction manual Appendix a, PowerPod-400 Serial Commands

Page 30

11.0 Appendix A

PowerPod-400 Serial Commands

Command	Name	Query		Response
	Channel 1 Display	C1	CH1 ddd.dd U of M GasID
	Channel 2 Display	C2	CH2 ddd.dd U of M GasID
	Channel 3 Display	C3	CH3 ddd.dd U of M GasID
	Channel 4 Display	C4	CH4 ddd.dd U of M GasID
			CH1 ddd.dd U of M GasID
	All Channels’ Display	C5	CH2 ddd.dd U of M GasID
	All Channels’ Display	C5	CH3 ddd.dd U of M GasID
			CH3 ddd.dd U of M GasID
			CH4 ddd.dd U of M GasID
SP1<dd.ddd>	Set Point - Channel 1	SP1	SP1 ddd.dd		notes 1, 2
SP2<dd.ddd>	Set Point - Channel 2	SP2	SP2 ddd.dd
SP3<dd.ddd >	Set Point - Channel 3	SP3	SP3 ddd.dd
SP4<dd.ddd >	Set Point - Channel 4	SP4	SP4 ddd.dd
A1H<dd.ddd >	Alarm Set Point, Ch1, High	A1H	A1H ddd.dd		notes 1, 2
A1L<dd.ddd >	Alarm Set Point , Ch1, Low	A1L	A1L ddd.dd
A2H<dd.ddd >	Alarm Set Point , Ch2, High	A2H	A2H ddd.dd
A2L<dd.ddd >	Alarm Set Point , Ch2, Low	A2L	A2L ddd.dd
A3H<dd.ddd >	Alarm Set Point , Ch3, High	A3H	A3H ddd.dd
A3L<dd.ddd >	Alarm Set Point , Ch3, Low	A3L	A3L ddd.dd
A4H<dd.ddd >	Alarm Set Point , Ch4, High	A4H	A4H ddd.dd
A4L<dd.ddd >	Alarm Set Point , Ch4, Low	A4L	A4L ddd.dd
HY1<ddd>	Hysteresis, Ch1	HY1	HY1 ddd
HY2<ddd>	Hysteresis, Ch2	HY2	HY2 ddd
HY3<ddd>	Hysteresis, Ch3	HY3	HY3 ddd
HY4<ddd>	Hysteresis, Ch4	HY4	HY4 ddd
UM1<dd>	Unit of Meas, Ch1	UM1	UM1 dd
UM2<dd>	Unit of Meas, Ch2	UM2	UM2 dd
UM3<dd>	Unit of Meas, Ch3	UM3	UM3 dd
UM4<dd>	Unit of Meas, Ch4	UM4	UM4 dd
GS1<ddd >	Gas ID, CH1	GS1	GS1 ddd
GS2<ddd >	Gas ID, CH2	GS2	GS2 ddd
GS3<ddd >	Gas ID, CH3	GS3	GS3 ddd
GS4<ddd >	Gas ID, CH4	GS4	GS4 ddd
IN1<d>	I/O Select, Ch1	IN1	IN1 d	rz - rfs	notes 6, 7
IN2<d>	I/O Select, Ch2	IN2	IN2 d	rz - rfs
IN3<d>	I/O Select, Ch3	IN3	IN3 d	rz - rfs
IN4<d>	I/O Select, Ch4	IN4	IN4 d	rz - rfs
FL1<d>	Filter Setting, Ch1	FL1	FL1 d
FL2<d>	Filter Setting, Ch2	FL2	FL2 d
FL3<d>	Filter Setting, Ch3	FL3	FL3 d
FL4<d>	Filter Setting, Ch4	FL4	FL4 d
ML1<d.dddd>	Multiplier, CH1	ML 1	ML 1 dddd.d		notes 1, 2
ML2<dd.ddd>	Multiplier , CH2	ML 2	ML 2 ddd.dd
ML 3<ddd.dd>	Multiplier , CH3	ML 3	ML 3 dd.ddd
ML 4<dddd.d>	Multiplier , CH4	ML 4	ML 4 d.dddd

164-122012 PowerPOD 400

Page 30 of 42

Image 30

Contents Teledyne Hastings Manual Print History Table of Contents Four to Twenty Milliamp Operation Power Quick Start InstructionsSafety Features Front Panel LockoutPower Selection Specifications PowerPod-400 Specifications TableFront Panel Channel Number Select KeysRear Panel Wiring PowerCommunications Alarms Transducer ConnectionsAnalog Signal Followers Manual Operation Power ON/OFFChanging the Command SET Point Override OpenSetting a Channel to Auto Control Setting a Channel to Directly Meter Incoming SignalsSetting a Channel to Display the Totalizer Function Mode Reset Value External/Remote Operation Choosing RS-232 CommunicationChoosing RS-485 Communication Display Setup Setup/Cal ModeEntering the SETUP/CAL Mode Blanking a Display Line/ChannelSetting A/D Conversion Rate Filter Selecting Unit-of-MeasureSelecting Gas ID Totalizer Setup Front Panel Lock OutCount Up to a Set Point RS-485 Settings External Communication SetupRS-232 Settings Count Down from a Set PointZero to Ten Volt Operation Selecting the Analog Signal LevelZero to Five Volt Operation Four to Twenty Milliamp OperationSetting a Single Channel’s Low Limit Setting Limit AlarmsSetting a Single Channel’s High Limit Setting a Single Channel’s HysteresisSetting Ratio Control Parameters Enabling Ratio ControlCalibrating a Channel to ITS Incoming Signals Resetting the Zero OnlyResetting the Span Only Resetting Zero and Span Setting a Multiplication FactorSerial Communication CommandsAlarm/Flag Queries Set Point QueriesPowerPOD PowerPod-400 Serial Commands Appendix aPowerPod-400 Serial Commands Contd Appendix a Notes ApppendixCB Name Rate TotalGas ID Table Page 1 Gas ID Table Page 2 Setting the Zero & Span PowerPod-400 Power Supply/Totalizer Appendix DZeroing Unit 4 to 20 mA Range Spanning Unit Transducer POWERPOD-400 PowerPOD Drawings Warranty Warranty Repair Policy