Teledyne powerpod 400 instruction manual Quick Start Instructions, Power

Page 5

1.0 Quick Start Instructions

Important – The PowerPod-400 comes calibrated from the factory according to your specifications. No set up is necessary unless you need to change the specs

1ea PowerPod-400 1ea AC power cord

1ea 15-pin, Hi Density, D-style connector

1ea 9-pin, D-style connector

1ea user’s manual

When unpacking the PowerPod, the package will

contain everything you need.

Connect a “known good” cable to the desired channel

(See next frame for pin-outs)

	J-1	Ch1

	J-2	Ch2

	J-3	Ch3

	J-4	Ch4

	J-5	Analog
	J-5	out
		out
	J-6	RS-232

	J-7	RS-485

	J-8	Alarms

	J-9	RS-485

Transducer Power,

Command and Analog

Signals.

Transducer Signal, Volts Only

Serial Com Port

Multi-drop com port (Daisy Chained)

Open-collector Alarms

Multi-drop com port (Daisy Chained)

1)	Check power setting switch on the back panel and make
	sure it is set appropriately.
2)	Ensure the power switch is off, and then connect the power

Pin-outs (see section 7)

cord.

Turn power switch to on position. If you have just

turned on the mass flow instrument and the

power, some settling is necessary.

		OPEN	1	2	3
	1	CLOSE	1	2	3
	1	CLOSE
		OPEN	4	5	6
	2	CLOSE	4	5	6
	2	CLOSE
		OPEN	7	8	9
	3	CLOSE	7	8	9
	3	CLOSE	0 .
		OPEN	0 .
	4	CLOSE	Power
			Power
			Pod

HASTINGS

1) Press the desired Channel # Key. Press the Auto key. (For Controllers)

2)Press the desired Channel # Key. Enter desired flow. Press the enter key.

164-122012 PowerPOD 400

Page 5 of 42

Image 5

Contents Teledyne Hastings Manual Print History Table of Contents Four to Twenty Milliamp Operation Quick Start Instructions PowerSafety Front Panel Lockout FeaturesPower Selection PowerPod-400 Specifications Table SpecificationsChannel Number Select Keys Front PanelRear Panel Communications WiringPower Transducer Connections AlarmsAnalog Signal Followers Changing the Command SET Point Power ON/OFFManual Operation Override OpenSetting a Channel to Display the Totalizer Function Setting a Channel to Auto ControlSetting a Channel to Directly Meter Incoming Signals Mode Reset Value Choosing RS-485 Communication External/Remote OperationChoosing RS-232 Communication Entering the SETUP/CAL Mode Setup/Cal ModeDisplay Setup Blanking a Display Line/ChannelSelecting Gas ID Setting A/D Conversion Rate FilterSelecting Unit-of-Measure Count Up to a Set Point Totalizer SetupFront Panel Lock Out RS-232 Settings External Communication SetupRS-485 Settings Count Down from a Set PointZero to Five Volt Operation Selecting the Analog Signal LevelZero to Ten Volt Operation Four to Twenty Milliamp OperationSetting a Single Channel’s High Limit Setting Limit AlarmsSetting a Single Channel’s Low Limit Setting a Single Channel’s HysteresisEnabling Ratio Control Setting Ratio Control ParametersResetting the Span Only Calibrating a Channel to ITS Incoming SignalsResetting the Zero Only Setting a Multiplication Factor Resetting Zero and SpanAlarm/Flag Queries CommandsSerial Communication Set Point QueriesPowerPOD Appendix a PowerPod-400 Serial CommandsPowerPod-400 Serial Commands Contd Appendix a Notes Name Rate Total ApppendixCBGas ID Table Page 1 Gas ID Table Page 2 Appendix D Setting the Zero & Span PowerPod-400 Power Supply/TotalizerZeroing Unit 4 to 20 mA Range Spanning Unit Transducer POWERPOD-400 PowerPOD Drawings Warranty Repair Policy Warranty