HP R-2A, R-2 MD01, R-3A, R-2 RDR manual Unit Status, Reset Unit, Logout

Page 18

RPC SERIES OWNER’S MANUAL

RPC SERIES QUICK START (RPC-3, RPC-3A, AND RPC-5)

________________________________________________________________________________

Access

Default password is <cr>; disabled.

NOTE : If user name and password are disabled (default), outlet users will have access to all admin functions.

Outlets

Outlet Status display – Default is enabled

 

Command Confirmation – Default is

 

enabled

 

Outlet Power-up Delay – programmable

 

elapse time before applying power to an

 

outlet after unit power-up, reset, or reboot.

 

Default is 0.

 

Name Outlets – Default name is Outlet 1,

 

Outlet 2, …

 

Display Outlet Users – A display of outlet

 

user assignments. Default is no users

 

assigned.

UNIT STATUS

The RPC sends a Unit Status Menu that

 

provides vital information about the RPC;

 

system status, network interface, logged user

 

status, and outlet status. Select the number

 

to review the status.

RESET UNIT

RESET UNIT allows changes to take effect.

 

It will not set the unit to factory default. It

 

will not disrupt power to the outlets

 

currently energized.

LOGOUT

Ends the session.

11

Image 18
Contents RPC-2 RDR RPC-3 RPC-3A RPC-5 BayTech Manual Publication #U140E125-03 JulyPage Page Page Page ADD User Delete User Change Password Vii Introduction to the Remote Power Control Switch RPC 115 VAC, 50/60 Hz, 15 Amp230 VAC, 50/60 Hz, 10 Amp RPC Series Quick Start RPC-2 and RPC-2A Quick StartOperation Or for the RPC-2A RPC Series Quick Start RPC-2 and RPC-2A RPC-2 MD01 and RPC-2 RDR Quick Start RPC-2 RDROperation Configuration Change PasswordRemote access using RPC-3, RPC-3A and RPC-5 Quick StartNetwork port Deletion of the admin user is prohibited Outlet ControlManage Users Change Outlet Change Password Default password is cr disabled8. Default is no outlets selected ListReset Unit Unit StatusLogout Installation Preparing the Installation SiteUnpacking Power Power ON/OFF State Power UP SequenceCircuit Breaker Cabling RJ-45 Cables and AdaptersRPC RJ-45 control port uses the following signals Computer/Terminal Adapter Crossed 8-pin Modular Cable Detailed Operation Configuration RPC-2 and RPC-2ARPC’s main menu allows the user to Controlling Receptacles Detailed Operation and Configuration Select #1, Change Password, and press Enter New Password To return to the RPC prompt, press any Key at the Enter Request promptSwitch, the RPC responds with the option to From the configuration menu, select #3Enable/Disable Confirmation Change the current status. Default isRPC-2 MD01 and RPC-2 RDR Local AccessUsing the EIA-232 Serial ConnectionRemote Access Using Modem Connections RPC’s main menu allows you to Responding Y for yes turns On Outlet If prompted, enter password. The following main menu appears Outlet RPC Config RPC Outlet Enter Request RPC-3 and RPC-3A and RPC-5 Using Network Using EIA-232Remote Access Port ConnectionOperation Detailed Operation and Configuration Password. When a successful username If this is not an initial setup and usernameAnd/or password have been enabled, you And/or password has been entered, the mainResponding Y for yes turns On Outlet Observe the status of Outlet 3 has changedTo On in the status menu Show in the User Management Menu, along If this is not an initial setup and optionalOutlet users have been added, they too will With the option to delete usersAdd User Delete userDefault password is cr Enter new password = 8 characters To change outlet access, enter numbers of outlets. If Select #3, Configuration. The following Configuration can be performed byAdmin user only via the serial port or Network port. From the RPC Main MenuDefault Subnet Mask is 0.0.0.0. If you fail Default Unit ID is RPC-3 AccessOutlet Operation Configuration Menu Disable Outlet Status Display? Y/N Unique set-up.Default outlet names are Name OutletsOutlet 1, Outlet 2, Outlet 3 . . . Outlet To return to the configuration menu, press any key RPC unit system status, network Status. In the event of problems withUnit status provides vital information about Interface, logged user status, and outletSystem Status Enter the number of the session to terminate RPC responds Reset the unit to load new configuration ChangesStatus Technical Support Outlet OUTLET3 Equipment SetupRPC Series Unit Model RPC Series Unit Serial Number OutletCall BayTech to get a Return Authorization Number REPACKAGING, Shipping and Returning to the FactoryInstructions for Repackaging and Shipping FCC Radio Frequency Interface Statement FCC Requirements for the RPC-2 MD01 and RDRFCC Radio Frequency Interface Statement Specifications Appendix aSpecifications Modem Command Summary Appendix BRobotic Modems Save modem’s configuration in non-volatile memory Rockwell Chip SET ModemsDiagnostic LED Indications Appendix CIndication Interpretation RPC Troubleshooting Guide Problem Symptom Cause SolutionAppendix D Appendix D RPC Troubleshooting Guide Cont’ Appendix D RPC Troubleshooting Guide Cont’ Appendix E- Drawings RPC-2RPC-2A RPC-2 MD01 RPC-2 RDR RPC-3 RPC-3A RPC3/3A/5 Ethernet Board RPC-5 Index Shipping