HP R-2 RDR, R-2A, R-2 MD01, R-3A manual Reset the unit to load new configuration, Changes

Page 64

RPC SERIES OWNER’S MANUAL

DETAILED OPERATION AND CONFIGURATION

________________________________________________________________________________

Outlet Status

The following table shows the status of all

 

outlets:

 

 

 

 

Outlet Status

 

 

 

 

Selection

Outlet

Outlet

Power

 

Number

Name

Number

Status

 

1

OUTLET 1

1

Off

 

2

OUTLET 2

2

Off

 

3

OUTLET 3

3

Off

 

4

OUTLET 4

4

Off

 

5

OUTLET 5

5

Off

 

6

OUTLET 6

6

Off

 

7

OUTLET 7

7

Off

 

8

OUTLET 8

8

Off

RESET UNIT

Reset the unit to load new configuration

 

changes.

 

 

 

From the main menu, select #5, “Reset

Unit.” The RPC responds:

Reset Unit? (Y/N)

Type “Y” for yes; allow approximately 5 seconds for unit reset.

Resetting the unit will not affect the power to energized outlets.

COMMAND SUMMARY In the following menu, “n” refers to selection number as displayed in Outlet Status. Any invalid input results in an input error message and returns the user to the command prompt.

From the RPC3> prompt in Outlet Control, type HELP. The RPC responds with the following command summary information.

57

Image 64
Contents RPC-2 RDR RPC-3 RPC-3A RPC-5 BayTech Manual Publication #U140E125-03 JulyPage Page Page Page ADD User Delete User Change Password Vii 115 VAC, 50/60 Hz, 15 Amp Introduction to the Remote Power Control Switch RPC230 VAC, 50/60 Hz, 10 Amp RPC-2 and RPC-2A Quick Start RPC Series Quick StartOperation Or for the RPC-2A RPC Series Quick Start RPC-2 and RPC-2A RPC-2 MD01 and RPC-2 RDR Quick Start RPC-2 RDROperation Configuration Change PasswordRPC-3, RPC-3A and RPC-5 Quick Start Remote access usingNetwork port Outlet Control Deletion of the admin user is prohibitedManage Users Change Password Default password is cr disabled 8. Default is no outlets selectedChange Outlet ListUnit Status Reset UnitLogout Preparing the Installation Site InstallationUnpacking Power Power UP Sequence Power ON/OFF StateCircuit Breaker Cabling RJ-45 Cables and AdaptersRPC RJ-45 control port uses the following signals Computer/Terminal Adapter Crossed 8-pin Modular Cable Detailed Operation Configuration RPC-2 and RPC-2ARPC’s main menu allows the user to Controlling Receptacles Detailed Operation and Configuration Select #1, Change Password, and press Enter New Password To return to the RPC prompt, press any Key at the Enter Request promptFrom the configuration menu, select #3 Enable/Disable ConfirmationSwitch, the RPC responds with the option to Change the current status. Default isLocal Access Using the EIA-232RPC-2 MD01 and RPC-2 RDR Serial ConnectionRemote Access Using Modem Connections RPC’s main menu allows you to Responding Y for yes turns On Outlet If prompted, enter password. The following main menu appears Outlet RPC Config RPC Outlet Enter Request RPC-3 and RPC-3A and RPC-5 Using EIA-232 Remote AccessUsing Network Port ConnectionOperation Detailed Operation and Configuration If this is not an initial setup and username And/or password have been enabled, youPassword. When a successful username And/or password has been entered, the mainObserve the status of Outlet 3 has changed Responding Y for yes turns On OutletTo On in the status menu If this is not an initial setup and optional Outlet users have been added, they too willShow in the User Management Menu, along With the option to delete usersAdd User Delete userDefault password is cr Enter new password = 8 characters To change outlet access, enter numbers of outlets. If Configuration can be performed by Admin user only via the serial port orSelect #3, Configuration. The following Network port. From the RPC Main MenuDefault Subnet Mask is 0.0.0.0. If you fail Default Unit ID is RPC-3 AccessOutlet Operation Configuration Menu Disable Outlet Status Display? Y/N Name Outlets Unique set-up.Default outlet names areOutlet 1, Outlet 2, Outlet 3 . . . Outlet To return to the configuration menu, press any key Status. In the event of problems with Unit status provides vital information aboutRPC unit system status, network Interface, logged user status, and outletSystem Status Enter the number of the session to terminate RPC responds Reset the unit to load new configuration ChangesStatus Technical Support Equipment Setup RPC Series Unit Model RPC Series Unit Serial NumberOutlet OUTLET3 OutletREPACKAGING, Shipping and Returning to the Factory Call BayTech to get a Return Authorization NumberInstructions for Repackaging and Shipping FCC Radio Frequency Interface Statement FCC Requirements for the RPC-2 MD01 and RDRFCC Radio Frequency Interface Statement Specifications Appendix aSpecifications Appendix B Modem Command SummaryRobotic Modems Save modem’s configuration in non-volatile memory Rockwell Chip SET ModemsAppendix C Diagnostic LED IndicationsIndication Interpretation Problem Symptom Cause Solution RPC Troubleshooting GuideAppendix D Appendix D RPC Troubleshooting Guide Cont’ Appendix D RPC Troubleshooting Guide Cont’ Appendix E- Drawings RPC-2RPC-2A RPC-2 MD01 RPC-2 RDR RPC-3 RPC-3A RPC3/3A/5 Ethernet Board RPC-5 Index Shipping