Lennox International Inc 506586-01 Heat Pump Control A175 Jumper and Terminal Descriptions

Page 24

Table 3. Heat Pump Control (A175) Jumper and Terminal Descriptions

Board ID

Label

Description

 

 

 

E12

PSC Fan

240 VAC output connection for outdoor fan.

 

 

 

E16

PSC Fan

240 VAC input connection for outdoor fan.

 

 

 

 

W

24VAC output for defrost auxiliary heat output.

 

 

 

 

L

Thermostat service light connection.

 

 

 

 

Y2

24VAC thermostat input/output for second stage operation of the unit.

 

 

 

 

Y1

24VAC thermostat input for first stage operation of the unit.

 

 

 

 

O

24VAC thermostat input for reversing valve operation

E18

 

 

DS

Humiditrol Input

 

 

 

 

 

C

24VAC system common

 

 

 

 

i−

Input/Output − RSBus data low. Used in communicating mode only with compatible indoor thermostat.

 

 

 

 

i+

Input/Output − RSBus data high. Used in communicating mode only with compatible indoor thermostat.

 

 

 

 

R

24VAC system power input

 

 

 

E19 and E20

O OUT

24 VAC output connection for reversing valve.

 

 

 

E21 and E22

LO−PS

Connection for low−pressure switch (2.4 milliamps @ 18VAC)

 

 

 

E31 and E32

Y1 OUT

24 VAC common output, switched for enabling compressor contactor.

 

 

 

E24 and E25

HS−PS

S87 connection for high−pressure switch (E25) and 24VAC (E24) to A177 R" input.

 

 

 

E26

FAN 1

First Stage and second stage basic and precision dehumidification ECM fan motor 24VDC output connection 1.

 

 

 

E27

FAN 2

Second stage basic and precision dehumidification ECM fan motor 24VDC output connection 2.

 

 

 

E28

FAN C

ECM common connection for ECM fan.

 

 

 

 

Six position square pin header. P4 provides connections for the temperature sensors.

 

 

 

 

DIS

Not used.

 

(YELLOW)

 

 

 

 

 

 

 

AMB 1

E30

AMB (BLACK)

AMB 2

 

(RT13)

 

 

 

Range is −40ºF to +140ºF

 

 

 

 

COIL

COIL 1

 

 

 

(BROWN)

COIL 2

 

(RT21)

Range is −40ºF to 140ºF. Sensor is clipped on a 5/16" copper return bend.

 

 

 

 

 

E33

Field Test

This jumper allows service personnel to defeat the timed off control, initiate or terminate a defrost and field

programming of unit nominal capacity feature.

 

 

 

 

 

 

 

Two position square pin header. When jumper is installed, a 30−second compressor shift delay which de−energizes

E37

Comp Shift

the compressor contactor output, second−stage solenoid output (if on) and the ECM fan outputs. After the timer

Delay

expires, the compressor contactor and ECM fan outputs are energized. If no jumper is installed, it changes the

 

 

 

reversing valve with de−energizing the outputs immediately.

 

 

 

 

50*

Seven position square pin header. E47 provides selection of the defrost terminate temperature based on the posi-

 

70

E47

tion of the selection jumper. The defrost termination temperature is measured by the defrost coil sensor. The jumper

 

90

termination pin is factory set at 50°F (10°C). If the temperature jumper is not installed, the default termination tem-

 

 

perature is 90°F (32°C). In addition, it provides selection points for enabling the field test mode.

 

100

 

 

 

 

 

W1

Short DS To R

Cut for Humiditrol (EDA) application. Use only in two−stage units.

 

 

 

* Factory default setting

 

 

 

 

Page 24

506586−01 10/10

Image 24
Contents Table of Contents GeneralHeat Pumps Unit Dimensions −− Inches mm Side View Access ViewModel Number Identification Base with Elongated LegsTypical Unit Parts Arrangement Control BOXUsing Manifold Gauge Set Operating Service ValvesShipping and Packing List Operating Angle Type Service Valve Operating Ball Type Service ValveTo Access Service Port Reinstall Stem CapRecovering Refrigerant from Existing System 1DISCONNECT PowerRecovering Refrigerant 2CONNECT Manifold Gauge SETUnit Placement Detail a Outside Unit Placement Placement, Slab Mounting and Stabilizing UnitRemoving and Installing Panels Stabilizing Unit on Uneven SurfacesRoof Mounting Louvered Panel Installation Louvered Panel RemovalDetail C Detail D Detail aNew or Replacement Line Set Refrigerant Line SETRefrigerant Line SET From Vertical to Horizontal Refrigerant Line SET Alling Horizontal RunsBrazing Connections 1PIPING Panel Removal and Preparing Line SET 2CAP and Core RemovalWrap Service Valves Flow NitrogenBraze Line SET 7PREPARATION for Next StepFlushing Line Set and Indoor Coil Flushing Line Set and Indoor CoilInstalling Indoor Expansion Valve Indoor Expansion Valve InstallationSensing Bulb Installation Equalizer Line InstallationLeak Test Line Set and Indoor Coil Leak TestEvacuating Line Set and Indoor Coil S S S SSize Circuit and Install Disconnect 2INSTALL ThermostatElectrical 24VAC Transformer3A. Route Control Wires Ting Route Control Wires Ting4ROUTE High Voltage and Ground Wires Typical XP17 Wiring Heat Pump Control A175 Jumpers and Terminals Heat Pump Control AGEHeat Pump Control A175 Jumper and Terminal Descriptions Field Control Wiring Flat metal jumperFurnace Control Connections for Testing and Charging Servicing Units Delivered Void of ChargeUnit Start−Up System RefrigerantCooling Mode Indoor Airflow Check Heating Mode Indoor Airflow CheckAdding or Removing Refrigerant Airflowindoor CoilUsing HFC−410A Weigh In Method Subcooling Charging MethodAir Handler / Coil Match ups and Targeted Subcooling Values Operating and Temperature Pressures PsigSystem Operations Defrost SystemResistor Location Sensor Temperature / Resistance Range Unit SensorsDefrost Calibration Sequence of Operations YESTest Pin E33 Functions S SLow Pressure S87 Switch Operation Or belowHigh Pressure Switch S4 Sequence of Operation Input Fault or Miswire Degrees Resistance Fahrenheit 136.3 2680 System Status, Fault and Lockout LED Codes DS11 and DS14 ATUS, Fault Lockout LED CodesResetting Fault and Lockout LED Codes DS15 and DS13 Ault Lockout LED CodesAlert Status Moderate Device225ºF 107ºC Lockout Vice removed or Clears after Field Configuration and Testing TroubleshootingFAN Motor B4 Test Procedure FAN Motor Control A177 OPERATION,Fan Motor Control Error/Fault LED Codes Fan Motor Control Stage LED Indicator CodesFan Motor Control RPM, LED Code and DC Voltage Output Fan Motor Control Flash and Pause DurationsTOP Grille or FAN Motor Mount Adjustment for FAN Clearance TOP Grille AdjustmentFAN Motor Position Adjustment Demand BeginsFAN Motor Control A177 PULSE−WIDTH Modulation PWM Testing for External Power to Fan Motor Control Strip StartTerminal FinishMaintenance Snow Guard Top CoverHomeowner SunSource Home Energy System XP17 Start−Up and Performance Checklist Cooling ModeHeating Mode START−UP Checks