Stovax Studio 22 manual Studwork for Cool Wall Installation KIT

Page 21

INSTALLATION INSTRUCTIONS

INSTALLATION

6.STUDWORK FOR COOL WALL INSTALLATION KIT

There is an optional Studio 22 Cool Wall Installation Kit available for installing the fire without a frame: Studio 22 BF Code No. 8727BFCW22. This consists of four metal brackets so that you can create a flush finish to the "edge" of the appliance.

For this cool-wall installation, the convected heat of the fire is channelled into the studwork enclosure and vented at the top.

The cool wall installation kit is provided unfinished. This allows the kit to be finished to match the fireplace decor.

Using the fixing kit:

•Fit the four metal brackets of the kit to the fire

•Line up the side brackets with the holes in the front flange of the appliance

•Secure to the flange using the nuts, washers and bolts provided, Diagram 20

20

AR2132

Note: Make sure the long side of the bracket is nearest the inside.

This now determines the width of your two vertical studwork supports. The kit has been designed so that non- combustible board can be taken right up to the edge of the four brackets, Diagram 21 & 22

21

AR2131

22

AR2082

•Ensure all clearances to combustible materials are maintained, Section 3, 3.1

•Decide on flue requirements

•Cut a hole for the flue exit - see Installation Instructions, Flue Assembly, Diagram 21

23

AR1902

•Secure the top bracket at each side into the studwork using the screws provided

•Secure the bottom bracket to the flange using the nuts, washers and bolts provided

Finally:

•Secure the outer part of the metal brackets into the studwork, see Diagram 20 inset

There is a deliberate gap at the top for convected heat.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Studio Studio 22 Balanced flue 8704BFLEC P8704BFLEC Covering the Following ModelFLUE CHECK FailGAS CHECK Increasing Temperature MAN ModeDecreasing Temperature GeneralTimer Mode Temp ModeLOW Battery Setting the TimeCleaning the Studio Changing the Studio BatteriesAll models Arrangement of Fuel BED Advice on Handling and Disposal of Fire CeramicsFire will not Light HOT SURFACESCovering the Following Models Technical SpecificationStudio 22 BF 8704BFLEC P8704BFLEC CATQty Description Fixing Kit containing Packing ChecklistSteel Frame Dimensions Size mm Profil Frame Dimensions Size mmBauhaus Frame Dimensions Size mm Flue and Chimney Requirements SITE REQUIREMENTSRear Exit Flue OptionsTOP Exits TOP Flue UP & OUT KITTOP Flue Vertical Offset KIT 8530/8530AN TOP Flue Vertical KIT 8524/8524ANExtra Flue Lengths GAS SupplyAppliance Location Installation Safety PrecautionsInstallation of the appliance AR2117 Distance to Combustible Material Stud Work InstallationSlips Flue system see Installation, Flue AssemblyApply a plaster finish to the chimney breast Studwork for Cool Wall Installation KIT Flue Assembly MAX Wall Thickness MINTOP Exit Vertical & Horizontal Flue TOP Exit Vertical Including OffsetAdd 10 mm to the outlet end Assembling the ApplianceArrangement of Fuel BED AR02123 Lighting the Studio Thermostatic Remote ControlCommissioning CommissioningSymptom Cause Remedy Servicing / Fault Finding ChartsServicing Requirements CheckFlame Failure Functional Check Ignition Functional CheckWindow Frame Assembly Replacing PartsGeneral Decorative FrameMaIN Control Assembly Vermiculite PanelsMaIN Burner Pilot Unit Assembly Pilot Burner BracketElectrode GAS Valve Ignition LeadPilot Injector ThermocoupleControl BOX Magnetic safety valveMain injector Primary Aeration PlateFollow , Main Control Assembly Pressure and Leak Testing the ApplianceComponent Short Spares List Studio3RD Service 1ST Service5TH Service 7TH ServiceMember of the Stovax Group
Top Page Image Contents