Monessen Hearth HBDV300N/PSC7, HBDV300N/PV7, HBDV400N/PSC7 Key Combinations for System Settings

Page 39

SIGNATURE COMMAND SYSTEM OPERATION INSTRUCTIONS

SYSTEM CONFIGURATION/SETUP

All System configuration/setup is done on the Command Center.

NOTE: When using On/Off wall switch, the switch must be in the ON position to perform all configuration set ups at the command center.

Intermittent/Standing Pilot Setup (Default intermittent)

1.Holding the ON button on the Command Center while turning on the master switch will toggle between standing pilot and intermittent pilot.

2.After the above operation, one beep (for standing pilot) or two beeps (for intermittent pilot) will be given as con- firmation.

Six-hour Safety Shutdown Option (Default ON)

1.The system comes preset from the factory with a six (6) hour shutdown from its last command of operation. This is done to prevent the fireplace from continuing to operate if unattended. You may disable this feature if you wish.

NOTE: By disabling this feature, your fireplace may continue to operate unattended.

2.When the master switch is in the ON position (“-”), pressing the ON button and the OFF button on the Command Center simultaneously will toggle between enabling and disabling the six-hour shutdown option.

3.After the above operation, one beep (for enabling the six-hour shutdown option) or two beeps (for disabling the six-hour shutdown option) will be given as confirmation.

Remote Transmitter Learn Function (Default OFF)

1.The RF receiver button located on the Control Board must be in the on position before the learn function can begin. Use paper clip to depress button. One beep for RF receiver ON or two beeps for RF receiver OFF will be given as confirmation. Refer to Figure 58 for location.

2.After the RF receiver is on, holding the OFF button on the Command Center while turning on the master switch will activate the learn function for the transmitter.

3.After the above operation, two beeps will be given and the green LED on the Command Center will flash for 10 seconds.

4.During the 10 seconds, press the OFF button on a transmitter to learn. Another two beeps will be given to confirm a successful learning. Refer to transmitter instructions for remote operations.

Shutting Off the Standing Pilot (Temporary Shut Off)

To shut off the standing pilot for service or summer shut down, press and hold the ON button on the Command Center for 3 seconds when the master switch is in the ON position (“-”) and the main burner is off.

Note: Pilot will resume the next time system is turned on.

Key Combinations for System Settings

NOTE: When On/Off wall switch is used, it must be in the On position to perform all system setups.

Function

operation

Default Setting

Intermittent/Standing

Hold the ON button while turning on the master switch

Intermittent

Pilot Setup

(Beep once for standing pilot, twice for intermittent pilot)

Pilot

Standing Pilot Temp.

Hold the ON button 3 seconds (when the master switch

 

Shutoff

on the main burner is off)

 

RF Remote Receiver

Push the RF receiver On/Off button on the control board

RF OFF

On/Off

Beep once for ON and beep twice for OFF

 

Learn Remote

Hold the OFF button while turning on the master switch

 

Transmitter

(Beep twice then press any handheld remote button)

 

6-hour safety

Press the ON button and OFF button simultaneously

ON

shutdown setup

(Beep once for ON, twice for OFF)

 

 

 

 

54D8000

39

Image 39
Contents HBDV7 Series Direct Vent Gas Fireplace Pre-Installation Information Check Gas Pressure Signature Command SystemMassachusetts Residents Only Important Safety Information InstallerOwner Code Approval Please Read the Following CarefullyNever connect unit to private non Known as wellhead gasHigh Elevations Product SpecificationsHBDV300 HBDV400 Framing DimensionsCold Climate Insulation PRE-INSTALLATION InformationFirebox framing Fireplace LocationOutlet grilles louvers. This may create a Clearances to combustiblesMantel Clearances Never obstruct or modify the air inlet orFinishing Material Secure Fireplace to Floor or FramingOptional TOP Vent Application Optional top vent applicationVenting Installation Information Installation precautionsGeneral Venting General Venting Information Termination Location Canadian Installations1 US Installations2USA Installations Canadian InstallationsTermination Clearances How to Use the Vent Graph Twist Lock PipesRefer to Page 21 for requirements for snorkels 1219 mm Vent InstallationRear Wall Vent Installation Twist Lock Pipe Rear Wall Vent ApplicationStep Rear Wall Vent Installations Flex Vent Pipe Vent configurations apply and must be strictly adhered toTop vent Sidewall Application + B = 17 Max Venting Installation Vertical Sidewall Installation Twist Lock PipeAlways install horizontal venting on a level plane Install the 4 flex then 7 flex to the termination Vertical Sidewall installation flex vent pipeBelow Grade Installations Vertical THROUGH-THE-ROOF APPLICA- TionDo not back fill around snorkel Vertical THROUGH-THE-ROOF Installation Roof Flashing Check gas type Install gas piping to fireplace / burner system locationFireplace Installation Natural GasPropane/LP Leaks Millivolt Check GAS Pressure and Electrical installationElectrical Wiring Do not use open flame to check for gasOptional DC Remote Systems Electrical InstallationRemote Wall mounted Switch Remote Wall SwitchWhat to do if YOU Smell GAS Initial lightingNever use an open flame to check for gas leak Flame Approved leak testing methodOperating Instructions Millivolt Never check for gas leak with openMain burner switch Lighting the burnerPilot position Or performing service. All wiring shall be Optional Accessory RequirementsElectrician. Main power must be off when Connecting to main electrical power supplyJunction BOX Wiring Command Center Wall InstallationWall Switch Installation Nected together if a wall switch is not Being used Blotsc Signature Command Blower Optional FAN Blower Systems Blot Automatic Thermostat BlowerFK-12 Manual Blower On next Command Center Operating Instructions Signature CommandFeatures Battery InstallationCommand Center Function Operation Default Setting Key Combinations for System SettingsFunction Operation Command Center OperationsSelf Diagnostics Chart FUNCTIONS/OPERATIONBrick installation Glass RemovalGlass Frame Removal Hazard Placement of Lava ROCK, Rock Wool and LogsDo not sprinkle the lava rock or ember Potential sooting, glass breakage and a fireFinal Installation Left Front Log #6 Installing Universal Andirons Burner, Pilot and Control Compart- ment Rock wool Vent SysteMGlass Door LogsStanding Pilot Ignition Symptom Possible Cause ActionTroubleshooting Signature Command System Firebox Components Replacement PartsDescription Qty Firebox componentsStanding Pilot Millivolt Control Accessories Fuel Conversion Kits Natural Gas to LPLP to Natural Gas Signature Command System HBDV300NSC7 HBDV300PSC7 HBDV400NSC7 HBDV400PSC7 Replacement Parts LogsDescription Qty Description Model Number Vertical Venting7TBLSCTK Horizontal VentingHBDV7 Series Direct Vent Gas Fireplace HBDV7 Series Direct Vent Gas Fireplace Carbon Monoxide Detector Requirements If Warranty Service is Needed Lifetime WarrantyFive Year Warranty Basic WarrantyModel EnerGuide Ratings Fireplace Efficiency % Mhsc