Wayne-Dalton 5140, 5120 installation instructions Horizontal Angle, Installing Q.I. Jamb Brackets

Page 12

2

Horizontal Angle

 

Tools Needed:

Position the horizontal angle as shown.

 

Hammer

Place tabs of horizontal angle in the key

slot of horizontal track. Using a hammer,

 

 

tap the horizontal angle towards the

 

curved end of the track until the holes in

 

track and angle are aligned. Set tracks

 

aside.

 

NOTE: For larger doors, a full length

 

horizontal angle may be spot welded to

 

the horizontal track. If the horizontal angle

 

is not welded, the horizontal angle will be

 

installed as shown.

Hole

Tabs

Horizontal

Angle

 

 

 

 

Key slot

 

 

 

 

Horizontal TRACK

Hole

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Horizontal

 

 

 

 

 

TRACK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Horizontal Angle

Horizontal

Horizontal

 

TRACK

 

angle

 

 

 

 

Horizontal

 

 

TRACK

 

Hammer

 

 

 

Tabs

3

Installing Q.I. Jamb Brackets

 

 

 

 

 

 

 

 

 

 

 

Tools Needed:

NOTE: If you have riveted track, skip this

 

 

 

 

 

 

step.

 

 

 

 

 

 

 

 

None

Measure the length of the vertical tracks.

 

 

 

 

 

 

Using the jamb bracket schedule,

 

 

 

 

 

 

 

determine the placement of the jamb

 

 

 

 

 

 

brackets for your door height and track

 

 

 

 

 

 

type. To install the jamb brackets,

 

 

 

 

 

 

 

align the twistlock tab on the quick

 

 

 

 

 

 

install jamb bracket with the quick

 

 

 

 

 

 

 

install feature in the track and turn the

 

 

 

 

 

 

bracket perpendicular to the track so the

 

 

 

 

 

 

mounting flange is toward the back (flat)

 

 

 

 

 

 

leg of the track.

 

 

 

 

left side shown

 

right side shown

 

 

 

 

 

 

 

 

 

Twistlock tab

 

 

 

 

Top

3rd SET HOLES

 

 

 

 

 

 

 

 

hole

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Middle

2nd SET HOLES

 

 

 

 

 

 

 

 

hole

 

 

 

 

 

 

 

 

 

 

 

 

Q.I. jamb bracket

 

 

 

 

 

 

 

JAMB BRACKET SCHEDULE

 

 

Bottom

 

 

 

1ST SET

2ND SET

3RD SET

hole

 

 

DOOR

 

 

 

 

 

 

 

 

 

 

1st SET HOLES

 

HEIGHT

JAMB BKT

POSITION

JAMB BKT

POSITION

JAMB BKT

POSITION

 

 

 

Quick install feature

 

 

 

 

 

 

 

 

 

7’0”

QIJB - 3

BOTTOM

QIJB - 7

TOP

NOT APPLICABLE

 

 

 

76” TRACK (1930 mm)

 

 

 

 

 

 

 

 

 

 

 

 

8’0”

QIJB - 3

MIDDLE

QIJB - 6

TOP

QIJB - 7

MIDDLE

 

 

 

88” TRACK (2235 mm)

 

 

 

 

 

 

 

 

 

 

 

12

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer.

 

To find your Wayne-Dalton dealer; refer to your local yellow pages / business listings or go to Find a dealer area online at www.wayne-dalton.com

Image 12
Contents 5120 Table of Contents Package Contents Door Section Identification Tools Required Torsion Spring Removal For Standard LiftFailure to use approved Winding bars can cause Spring energy to be releasedUsing an electric drill High Counter cover when countingBracket will always have a drive gear Head will be pluggedTorqueMaster Spring RemovalExtension Spring Removal Removing the Old DoorPreparing the Opening Installation Attaching Quick Install FlagAngle to Vertical Track Installing Q.I. Jamb Brackets Horizontal AngleDrums Bottom SectionVertical Track Stacking SectionsTop Brackets BarBar Asymmetrical Operator BracketTop Section Tools Needed To install horizontal track, place To the slot in the flagangle usingPortion of horizontal track down to Remove the nail that was temporarilyTorqueMaster Spring Tube Center Bracket BushingIdrive Installation Plug the motor power cord into OpenerGarage looking out Right hand end of the TorqueMasterCable Drum Installation Drive Gear Installation End BracketsCounter Installation Securing Center Bracket AssemblyPositioning Support Bracket Attaching Disconnect Cables Mounting DisconnectHandle Bracket Attaching Disconnect Handle Cable Adjustments Securing DoorFailure to place vice clamps Onto vertical Track canSetting Spring Tension Winding Bolt RotationDrum Wrap Installation Rear SupportAdjustments to the springs Installation InstructionsParallel with door Or door stop too tightly against faceSide Lock Sold Separately Step Plate Sold Seperately Pull RopeDetermine the Wayne-Dalton Track radius being usedAppropriate 1/2 1 room permitting above of the high Trolley to operator bracketTrolley Installation for Low Headroom Trolley Operator Opens if Photoelectric EYE SystemOperator Rail Suitable mountingCleaning Cleaning Your Garage DoorPainting Maintenance PaintingLimited Warranty Models 5120